APPLICABLE STANDARD
IP65
Operating
Storage
-55C to +85C (Note2)
-40C to +105C (Note1)
temperature range
temperature range
RATING
Voltage
AC 300 V , DC 300 V
―
―
12.5A / 1Pin AWG#18(UL1007)時
3A / 50Pin AWG#18(UL1007)時
AWG#18 to AWG#22
(UL-STYLE : UL1007)
Current
Applicable cable
SPECIFICATIONS
ITEM
TEST METHOD
REQUIREMENTS
QT AT
CONSTRUCTION
General Examination
Marking
X
X
X
X
Visually and by measuring instrument.
Confirmed visually.
According to drawing.
ELECTRICAL CHARACTERISTICS
X
X
X
X
-
-
-
-
5 m MAX. (Signal and power contact)
50 m MAX. (Ground contact)
5000 M MIN.
Contact Resistance
100 mA (DC OR 1000 Hz) MAX.
Insulation Resistance
Voltage Proof
500 V DC.
2200 V AC. for 1 min.
No flashover or breakdown.
MECHANICAL CHARACTERISTICS
Contact Insertion and
Insertion force : 3 N MAX.
X
X
-
-
Applicable contact.
Withdrawal Forces
Withdrawal force : 1 N MIN.
CONNECTOR INSERTION AND
WITHDRAWAL FORCES
Insertion force : 98
N MAX.
Applicable connector.(Without the lock lever)
1
1
Withdrawal force : 14.7 N MIN.
Apply axial pull out force at the speed rate of
Contact(Lance)
X
-
25mm/min to the contact and mesure the force when the 29.4N MIN
contact is pulled out.
1
Retention Forces
Crimp the cable only at the conductor, and retention ① AWG#18 : 89
force shall exceed the specification when pull force ② AWG#20 : 57.9 N MIN.
is applied. ③ AWG#22 : 35.6 N MIN.
Apply pull force of 98 N in mating direction for a ① Contacts should be retained.
N MIN.
Conductor Pressure Bonding
Forces
X
X
X
-
-
-
Cable Clamp Strength
Mechanical Operation
minute.
② No damage. Crack and looseness of parts.
① Change in contact resistance of Contacts
: 10 m MAX.
500 times insertions and extractions.
② No damage. Crack and looseness of parts.
Frequency : 10 to 55 Hz, singe amplitude 0.75 mm,
At 2 h, for 3 axial directions.
① No electrical discontinuity of 10 s.
② No damage. Crack and looseness of parts.
X
X
-
-
Vibration
Shock
(Reference for appended figure)
① No electrical discontinuity of 10 s.
② No damage. Crack and looseness of parts.
In opposite directions of each 3 both axis for
3 times at 490 m/s2 duration of pulse 11 ms.
COUNT
DESCRIPTION OF REVISIONS
DESIGNED
TY.MIURA
CHECKED
DATE
1
△
5
DIS-E-00003614
TU.TANIGUCHI
NM.NISHIMATSU
NM.NISHIMATSU
P.EKSOURIYA
P.EKSOURIYA
20201201
20170124
20170124
20170124
20170124
REMARK
Above spesification shows the values in assembled condition with “PQ50W” series.
APPROVED
CHECKED
DESIGNED
DRAWN
In case of using for other series of connector , the specification is based on each series.
Unless otherwise specified , refer to IEC 60512(JIS C 5402)
1
Note QT:Qualification Test AT:Assurance Test X:Applicable Test
DRAWING NO.
PART NO.
CODE NO.
ELC-129312-00-00
PQW-CM(15.0)
SPECIFICATION SHEET
HIROSE ELECTRIC CO., LTD.
1
△
1/3
CL0236-2104-0-00
FORM HD0011-2-1