®
Design Idea DI-19
Lin k S w it c h Low Cost 1.5 W
CV/CC Charger or Adapter
Topology
Flyback
Device
Power Output
Input Voltage
Output Voltage
Application
Charger/Adapter
1.5 W
85-265 VAC
LNK501
5.5 V
LinkSwitchderivesallfeedbackinformationfromtheprimary.
During output diode conduction, the output voltage
transformed through the turns ratio is sampled and held by
C4. The feedback voltage across C4 (VOR) is converted into
feedbackcurrentbyR2andfedintotheCONTROLpin. This
feedbackcurrentregulatestheoutputbyPWMcontrolduring
CV operation, and by reducing the internal current limit
during CC operation. Below an output voltage of ~2 V,
LinkSwitchentersauto-restart,limitingaverageoutputcurrent
to <50 mA. The nominal transition from CV to CC occurs at
5.5 V, 0.27 A. The output envelope characteristic and
specification limits are shown in Figure 2.
Design Highlights
• Replaces a linear transformer based supply at the same or
lower cost but with much higher performance
• <0.3Wconsumptionatzeroloadmeetsworldwideguidelines
(EC’s 0.3 W, USA’s 1 W for example)
• Extremely simple circuit – only 15 components for
production-worthy design
• Primary based CV/CC output – no secondary sense
components required
• ±10% output voltage and ±22% output current tolerances at
peak power point
• Fullyprotectedforthermal,shortcircuitandopenloopfaults
• >62% efficiency (>70% with R1 replaced by an inductor)
• Meets CISPR22B/EN55022B EMI limits with low cost
resistive input filter
• Ultra-low leakage current design <5 µA
• EE13 core for low cost and small size
TogetherwithD3,C4andR2arealsopartoftheprimaryclamp,
limiting the peak drain to source voltage due to leakage
inductance. Resistor R3 filters the leading edge leakage
inductance spike, reducing the error in the feedback voltage.
The CONTROL pin capacitor C3 provides energy storage for
supply start-up and sets auto-restart timing during fault
conditions.
Operation
The AC input is rectified and filtered by D1, D2, C1 and C2.
Conducted EMI filtering is provided both by a π filter (C1, R1
and C2) and a differential filter (RF1 and C1). Together with
ashieldinthetransformer(formedfrompartoftheprimary)the
designmeetsconductedEMIlimitswithnoY-capacitorbetween
primary and secondary. Resistor RF1 also functions as a fuse.
Key Design Points
•
Select transformer turns ratio to give a VOR of 40 V
to 60 V. Lower values reduce power capability; higher
values increase no-load consumption.
• R2 provides 2.3 mA into the CONTROL pin at the peak
power point at 85 VAC. The value can be adjusted to
center the output voltage.
R1
68 Ω
Flameproof
Lin k S w it c h
T1
5.5 V, 0.27 A
D
S
1
C
U1
LNK501
5
6
104T
C3
0.22 µF
34 AWG
15 T
30 AWG
T.I.W.
C5
D1
1N4007
4
220 µF
12T
C4
RF1
10 Ω
Fusible
16V
2 x 30 AWG
0.1 µF
100 V
FILM
R2
21 kΩ
RTN
3
C1, C2
2.2 µF
400 V
85-265
VAC
EE13
D4
D3
1N4937
LP = 1.36 mH UF4002
1A 100V
D2
1N4007
R3
100 Ω
PI-3367-091602
Figure 1. LinkSwitch 1.5 W Charger Power Supply: 85 VAC to 265 VAC Input, 5.5 V, 0.27 A Output
September 2002
DI-19
www.powerint.com
5秒后页面跳转
MAX487芯片引脚图及功能、应用领域详解
IR2110驱动芯片引脚图及功能、电路图详解
74LS74是什么芯片 74LS74引脚图及功能表
CD4511芯片引脚图及功能、电路图解析
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
