Document 522 -1
For 30 Watt
Applications
PoE Plus Transformers
• Designed to meet 30 W PoE objectives of IEEE 802.3at.
• Operates at 250 kHz with 36 – 72 Volts input
• Isolation: 1500 Vrms pri to sec; 500 Vrms pri to aux
Designer’s Kit C398 contains three samples of each part.
Core material Ferrite
Terminations RoHS tin-silver over tin over nickel over phos
bronze. Other terminations available at additional cost.
Weight 11.9 g
Ambient temperature –40°C to +125°C
Storage temperature Component: –40°C to +125°C.
Packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 175 per 13″ reel Plastic tape: 44 mm wide,
0.4 mm thick, 32 mm pocket spacing, 11.9 mm pocket depth
PCB washing Only pure water or alcohol recommended
Inductance Inductance
Leakage
at 0 A2
at Ipk3
inductance5
Ipk3
DCR max (Ohms)
Turns ratio6
Part
number1
±10% (µH)
min (µH)
pri4
sec4
aux
max (µH) pri : sec pri : aux (A)
Output7
POE300F-33L_
POE300F-50L_
POE300F-12L_
POE300F-19L_
POE300F-24L_
42.0
42.0
42.0
42.0
42.0
37.8
37.8
37.8
37.8
37.8
0.070 0.0023 0.220
0.069 0.0050 0.225
3.00
1.60
0.545
0.430
0.310
1 : 0.09 1 : 0.33
1 : 0.14 1 : 0.33
1 : 0.33 1 : 0.33
1 : 0.56 1 : 0.33
1 : 0.67 1 : 0.33
2.6
2.6
2.6
3.3 V, 9 A
5 V, 6 A
12 V, 2.5 A
0.061 0.015
0.060 0.037
0.060 0.055
0.195
0.195
0.195
2.6 19.5 V, 1.5 A
2.6 24 V, 1.25 A
1. When ordering, please specify packaging code:
POE300F-50LD
12
11
10
1
2
Packaging: D = 13″ machine-ready reel. EIA-481 embossed plastic
Pri
Sec
tape (175 parts per full reel).
B = Less than full reel. In tape, but not machine ready. To
have a leader and trailer added ($25 charge), use
code letter D instead.
9
8
7
4
3
5
2. Inductance is for the primary, measured at 250 kHz, 0.7 Vrms, 0 Adc.
3. Peak primary current drawn at minimum input voltage.
4. DCR is with the windings connected in parallel.
Aux
5. Leakage inductance is for the primary winding with the secondary
windings shorted.
6
6. Turns ratio is with the primary and the secondary windings connected in
parallel.
7. Output is with the secondary windings connected in parallel. Output of
the auxiliary winding is 12 V
The primary windings and the secondary
windings are to be connected in parallel
on the PC board.
8. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Specifications subject to change without notice.
Please check our website for latest information.
Document522-1 Revised10/29/08
© Coilcraft, Inc. 2009