25W Single Output LED Power Supply
PLD-25 series
Features :
Universal AC input / Full range (up to 295VAC)
Built-in active PFC function
Constant current design
Protections: Short circuit / Over temperature
Cooling by free air convection
Fully isolated plastic case
IP30 design
Class
power unit, no FG
Class 2 power unit
100% full load burn-in test
Low cost
High reliability
Suitable for dry / damp locations
3 years warranty
110
F
SELV
IP30
( for PLD-25-350/700 )
( except PLD-25-350/700 )
SPECIFICATION
MODEL
PLD-25-350
PLD-25-700
PLD-25-1050
PLD-25-1400
RATED CURRENT
350mA
700mA
1050mA
1400mA
OPERATING VOLTAGE RANGE 36 ~ 58V
24 ~ 36V
0 ~ 700mA
16 ~ 24V
0 ~ 1050mA
12 ~ 18V
0 ~ 1400mA
CURRENT RANGE
CURRENT ACCURACY
RATED POWER
0 ~ 350mA
5.0%
OUTPUT
20.3W
25.2W
2.7Vp-p
50V
25.2W
2.2Vp-p
35V
25.2W
2Vp-p
25V
RIPPLE & NOISE (max.) Note.1 4.6Vp-p
NO LOAD OUTPUT VOLTAGE (max.) 63V
SETUP TIME
1500ms / 230VAC 3000ms / 115VAC at full load
VOLTAGE RANGE
90 ~ 295VAC
47 ~ 63Hz
127 ~ 417VDC
FREQUENCY RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INRUSH CURRENT(max.)
LEAKAGE CURRENT
PF>0.98/115VAC, PF>0.92/230VAC, PF>0.91/277VAC at full load (Please refer to "Power Factor Characteristic" curve)
INPUT
85%
86%
85%
84%
0.6A/115VAC 0.3A/230VAC
40A/230VAC
<0.5mA / 240VAC
Hiccup mode, recovers automatically after fault condition is removed.
95 10 (RTH1)
SHORT CIRCUIT
PROTECTION
ENVIRONMENT
OVER TEMPERATURE
Protection type : Shut down o/p voltage, re-power on to recover
-30 ~ +60 (Refer to "Derating Curve")
20 ~ 95% RH non-condensing
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
-40 ~ +80 , 10 ~ 95% RH
0.03%/ (0 ~ 50
)
10 ~ 500Hz, 2G 12min./1cycle, period for 72min. each along X, Y, Z axes
UL8750, CSA C22.2 No. 250.0-08(except for PLD-25-350, PLD-25-700), ENEC EN 613471, EN 61347-2-13, IP30 approved ;
design refer to UL60950-1, TUV EN60950-1
SAFETY STANDARDS
SAFETY &
EMC
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
EMC EMISSION
I/P-O/P:3.75KVAC
I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH
Compliance to EN55015, EN61000-3-2 Class C ( 75% load) ; EN61000-3-3, FCC part 18 non-consumer equipment
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024,EN61547, light industry level, criteria A
EMC IMMUNITY
MTBF
968.6Khrs min. MIL-HDBK-217F (25
84*57*29.5mm (L*W*H)
)
OTHERS
NOTE
DIMENSION
PACKING
0.19Kg; 72pcs/14.7Kg/0.75CUFT
1. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
2. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers.
File Name:PLD-25-SPEC 2012-03-20