SMT Power Inductors
Power Beads - PGL6312XXXHLT Series
Current Rating: Over 90Apk
Inductance Range: 90nH to 150nH
Height: 10.0mm Max
Footprint: 6.5mm x 6.5mm Max
Electrical Specifications @ 25°C — Operating Temperature - 40°C to +130°C 7
Saturation Current5
(A TYP)
Inductance1
@ 0ADC
Inductance2
@Irated
Irated3
DCR4
Heating Current6
(A TYP)
Part
Number
(ADC)
(mΩ nominal)
(nH +/- 15%)
(nH TYP)
25°C
100°C
77
PGL6312.900HLT
PGL6312.101HLT
PGL6312.121HLT
PGL6312.151HLT
90
100
120
150
90
68
82
68
68
82
52
90
80
69
52
70
60
46
0.17 +/- 10%
70
102
NOTES:
1. Inductance measured at 100kHz, 100mVrms.
7. In high volt*time applications, additional heating in the component can occur due
to core losses in the inductor which may neccessitate derating the current in order
to limit the temperature rise of the component. To determine the approximate total
losses (or temperature rise) for a given application, the coreloss and temperature rise
curves can be used.
2. Inductance at Irated is the value of the inductance at 25°C at the listed rated current.
3. The rated current as listed is either the saturation current (25°C or 100°C) or the heat-
ing current depending on which value is lower.
2.
4. The nominal DCR is measured at point
drawing.
, as shown below on the mechanical
8. Parts with the HLT suffix are sold in tape and reel packaging. Pulse complies to
industry standard tape and reel specification EIA-481.
5. The saturation current is the typical current which causes the inductance to drop by
20% at the stated ambient temperatures (25°C, 100°C ). This current is determined by
placing the component in the specified ambient environment and applying a short
duration pulse current (to eliminate self-heating effects) to the component.
6. The heating current is the DC current which causes the part temperature to increase by
approximately 40°C when used in a typical application.
The tape and reel for this product has a width (W=16mm), pitch (Po=12mm) and depth
(Ko=6.8mm). Samples of these parts can be ordered by removing the HLT suffix and
replacing with HL.
9. The temperature of the component (ambient plus temperature rise) must be within
the stated operating temperature range.
10. Sample Value only. Guaranteed by Design and not tested in production
Schematic
Mechanical
PGL6312.XXXHLT
6.5 MAX
6.5 MAX
.XXXHL
1
2
10.0 MAX
Weight:
2.74grms
400/ Reel
0.10
2 SURFACES
Tape &Reel:
Dimensions:
DCR MEASURE POINT
mm
2.6
6.6
Unless otherwise specified ,
all tolerances are 0.25
3.70 0.2
1.75 REF
4.2
2.75 REF
P911.A (06/21)
PulseElectronics.com
1
5秒后页面跳转
AO3401场效应管参数、引脚图、应用原理图
BT131可控硅参数及引脚图、工作原理详解
74LS32芯片参数、引脚图及功能真值表
全球首块英伟达H200交付 黄仁勋“送货上门”
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
