Version 1.4 2010
Features
PEX 8615 General Features
o 12-lane PCI Express switch
- Integrated 5.0 GT/s SerDes
o Up to 12 configurable ports
o 19 x 19mm2, 324-ball HSBGA
o Typical Power: 1.79 Watts
PEX 8615
PEX 8615 Key Features
Flexible & Versatile 12-lane 12-port PCI Express® Switch
o Standards Compliant
- PCI Express Base Specification r2.0
(Backwards compatible with PCIe
r1.0a/1.1)
- PCI Power Management Spec r1.2
- Microsoft Vista Compliant
- Supports Access Control Services
- Dynamic link-width control
o Integrated DMA Engine
- Four DMA Channels
The ExpressLane™ PEX 8615 device offers PCI Express switching capability
enabling users to add scalable high bandwidth non-blocking interconnection to a
wide variety of applications including control planes, communication platforms,
servers, storage systems and embedded systems. The PEX 8615 is well suited for
fan-out, aggregation, peer-to-peer, and intelligent I/O module applications.
Low Packet Latency & High Performance
The PEX 8615 architecture supports packet cut-thru with a maximum latency of
140ns. This, combined with large packet memory and non-blocking internal switch
architecture, provides full line rate on all ports for low-latency applications such as
communications and servers. The low latency enables applications to achieve high
throughput and performance. In addition to low latency, the device supports a max
payload size of 2048 bytes, enabling the user to achieve even higher throughout.
- Internal Descriptor Support
- DMA function independent from
transparent switch function
- 64-bit Addressing
- Prefetch Descriptor Mode
- Up to 4.0 GB/s throughput per channel
o Dual-Host & Fail-Over Support
- Configurable Non-Transparent port
(NTB)
- Moveable upstream port
- Crosslink port capability
o High Performance
- Cut-Thru latency: 140ns
- 2KB max payload size
Integrated DMA Engine
The PEX 8615 provides a versatile and powerful DMA engine built in to the device
which can be used as a stand alone DMA engine. The DMA engine removes the
burden resulting from having to move data between devices away from the
processor. This allows the processor to perform computational tasks instead. The
four DMA channels can support high data rate transfers between IO devices
connected to any of the available ports in the PEX8615. Additionally, the DMA
engine in the PEX 8615 can be used to complement the DMA engine in the
processor by providing additional DMA channels for higher performance.
- Read Pacing
- Dual-Cast
o Flexible Configuration
- 12 flexible & configurable ports
(x1 or x4)
- Configurable with strapping pins,
EEPROM, I2C, or Host software
- Lane and polarity reversal
o PCI Express Power Management
- Link power management states: L0, L0s,
L1, L2/L3 Ready, and L3
Data Integrity
The PEX 8615 provides end-to-end CRC protection (ECRC) and Poison bit support
to enable designs that require guaranteed error-free packets. PLX also supports
data path parity and memory (RAM) error correction as packets pass through the
switch.
- Device states: D0 and D3hot
o Spread Spectrum Clock Isolation
- Dual clock domain
o Quality of Service (QoS)
- Two Virtual Channels (VC) per port
- Eight Traffic Classes per port
- Weighted Round-Robin Port & VC
Arbitration
o Reliability, Availability, Serviceability
- All ports Hot-Plug capable thru I2C
(Hot-Plug Controller on every port)
- Data path protection
- Memory (RAM) error correction
- Port Status bits and GPIO available
- Per port error diagnostics
- Performance monitoring
(per port payload & header counters)
Dual-Host and Fail-Over Support
The PEX 8615 supports full non-transparent bridging (NTB) functionality to allow
implementation of multi-host systems and intelligent I/O modules in applications
which require redundancy support such as communications, storage, and servers.
Non-transparent bridges allow systems to isolate host memory domains by
presenting the processor subsystem as an endpoint rather than another memory
system. Base address registers are used to translate addresses; doorbell registers are
used to send interrupts between the address domains; and scratchpad registers are
accessible from both address domains to allow inter-processor communication.
Interoperability
The PEX 8615 is designed to be fully compliant with the PCI Express Base
Specification r2.0 and is backwards compatible to PCI Express Base Specification
r1.1 and r1.0a. Additionally each port supports auto-negotiation, lane reversal and
polarity reversal. Furthermore, the PEX 8615 is designed for Microsoft Vista
compliance. All PLX switches undergo thorough interoperability testing in PLX’s
Interoperability Lab and compliance testing at the PCI-SIG plug-fest to ensure
compatibility with PCI Express devices in the market.
5秒后页面跳转
STM32F030C6芯片介绍：主要参数分析、引脚配置说明、功耗及封装
PCF8591数据手册解读：参数、引脚说明
一文带你了解ss8050参数、引脚配置、应用指南
深入解析AD7606高性能多通道模数转换器：资料手册参数分析
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
