Pl tronics, Inc.
.
19013 36th Ave. W, Suite H Lynnwood, WA 98036 USA
Manufacturer of High Quality Frequency Control Products
PE2245B PECL Series
10 Pad Leadless Surface Mount Clock Oscillator, see PE1145B for 6 Pad
Differential PECL Output with or without Enable/ Disable Function
–
10.00 MHz 170.00 MHz
See PE1145T for higher frequencies
All Connor-Winfield EE94-5XX Pinouts Available
Standard Specifications
Overall Frequency Stability
± 50 PPM, ± 25 PPM, ± 20 PPM over Operating Temperature Range
-
°
Operating Temperature Range 0 to +80 C is standard, but can be extended to 40 to +85°C for certain frequencies
Supply Voltage (Vcc)
Supply Current (Icc)
Jitter
3.3 volts ± 10% standard, but 5.0 volts or 2.5 volts also available
³
60 to 70 mA typical, 90 mA maximum for 70 MHz. For < 70 MHz, consult factory
1 pS RMS maximum, from 12 kHz to 20 MHz from carrier for ³ 70 MHz. For < 70 MHz, consult factory
Output must be terminated into 50 ohms to (Vcc - 2.0 V). See Test Circuit 5 and Note 1.
Output enabled when E/D Pin is open or at CMOS Logic “1”;
Output Load
Enable/Disable Option (E/D)
(as applicable)
Output disabled when E/D Pin is at CMOS Logic “0”.
Symmetry
Tr & Tf
Logic “1”
45/55% to 55/45% at 50% of Vcc level standard, tighter symmetry available
Output Waveform
PECL with Differential Output
(see Waveform 2)
³
1.0 nS max (20 to 80%) for 70 MHz. For < 70 MHz, consult factory
Vcc - 1.025 volts minimum
Vcc - 1.620 volts maximum
Logic “0”
Note 1:
In the typical PECL 100K logic output Voh is 2.35 volts and Vol is 1.60 volts at 3.3 Vcc. The center voltage of the PECL is therefore1.975 volts.
If a 50 ohm resistor is placed between the output and Vcc – 2 volts (1.3 volts), the current through the resistor is (1.975 – 1.3) / 50 = 13.5 mA.
±
The same load can be simulated by a resistor of 147 1% ohms to ground (1.975 / 0.0135 = 146.29 ohms). If additional load current is placed
on the output, its load current must be subtracted from the 13.5 mA to calculate a new load resistor. Using similar calculations, use 274 ± 1%
ohms to ground for 5.0V operation.
Part Numbering Guide
Portions of the part number that appear after the frequency may not be marked on part (C of C provided)
PE22 45 B Y - 70.0M - XXX (Internal Code or blank)
Model
Packaging
(Pinout Option)
Frequency in MHz
Tray or
PE20 PE23
PE21 PE24
PE22
24mm tape,
16mm pitch
Special Specifications (choose all that apply)
°
E: Extended Operating Temperature Range (- 40 to +85 C)
F: 47.5 /52.5% Symmetry at 50% of Vcc
V: Supply Voltage of 3.3 volts ± 10%
W: Supply Voltage of 2.5 volts ± 5%
Y: Supply Voltage of 5.0 volts ± 10%
Frequency Stability
45 = ± 50 PPM
44 = ± 25 PPM
20 = ± 20 PPM
Consult factory for available frequencies and specs. Not all options available for all frequencies. A special part number may be assigned.
Frequency Stability is inclusive of frequency shifts due to calibration, temperature, supply voltage, shock, vibration and load
Mechanical: inches (mm)
not to scale
Solder Pads
Due to part size and factory abilities, part marking may vary from lot to lot and may contain our part number or an internal code.
Q
Vcc
*
10
9
8
7
6
6
7
8
9
10
PLE
.05
(1.3)
N.C.
N.C.
N.C.
N.C. N.C.
2
1
5
4
3
1
2
3
4
5
GND
*
.560 (14.23) MAX
.217 (5.5)
MAX
July 2002
.400 (10.16)
For Best Performance,
C-W
Option '0'
'1'
'2'
'3'
'4'
Pin PE20 PE21 PE22 PE23 PE24
2
*
PE2245B Series Pinout Options
Connor-Winfield EE94-5XX Equivalents
Do NOT allow any traces other than ground
under oscillators (Even in buried layers)
N.C. N.C. E/D QN E/D
6
N.C. QN N.C. N.C. QN
(425) 776 -1880, Fax: (425) 776-2760, ple-sales@pletronics.com, www.pletronics.com
Pl tronics, Inc.
5秒后页面跳转
AO3401场效应管参数、引脚图、应用原理图
BT131可控硅参数及引脚图、工作原理详解
74LS32芯片参数、引脚图及功能真值表
全球首块英伟达H200交付 黄仁勋“送货上门”
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
