65W Dual Output Switching Power Supply
PD-65 series
Features :
Universal AC input / Full range
Low leakage current<0.5mA
Protections: Short circuit / Overload / Over voltage
Cooling by free air convection
100% full load burn-in test
Fixed switching frequency at 65KHz
2 years warranty
SPECIFICATION
MODEL
PD-65A
PD-65B
OUTPUT NUMBER
CH1
CH2
CH1
CH2
DC VOLTAGE
5V
12V
5V
24V
RATED CURRENT
CURRENT RANGE
RATED POWER
5.5A
2.8A
3.5A
2A
0.4 ~ 7A
61.1W
0.2 ~ 3.2A
0.4 ~ 6A
65.5W
0.2 ~ 2.6A
OUTPUT POWER (max.)
Rated output power for convection; 72W with 18CFM min. Forced air
OUTPUT
RIPPLE & NOISE (max.) Note.2 50mVp-p
VOLTAGE ADJ. RANGE
VOLTAGE TOLERANCE Note.3 4.0%
120mVp-p
50mVp-p
CH1:4.75 ~ 5.5V
4.0%
150mVp-p
CH1:4.75 ~ 5.5V
7.0%
2.0%
4.0%
7.0%
2.0%
4.0%
LINE REGULATION
LOAD REGULATION
SETUP, RISE TIME
HOLD UP TIME (Typ.)
VOLTAGE RANGE
1.0%
1.0%
3.0%
3.0%
800ms, 20ms at full load
60ms at full load
90 ~ 264VAC
47 ~ 440Hz
78%
127 ~370VDC
FREQUENCY RANGE
EFFICIENCY(Typ.)
81%
INPUT
1.5A/115VAC
0.9A/230VAC
AC CURRENT (Typ.)
INRUSH CURRENT (Typ.)
COLD START 20A/115VAC
<0.75mA
40A/230VAC
LEAKAGE CURRENT
OVERLOAD
73 ~ 105W rated output power
Protection type : Hiccup mode, recovers automatically after fault condition is removed.
CH1: 5.75 ~ 6.75VDC on CH1
PROTECTION
OVER VOLTAGE
Protection type : Hiccup mode, recovers automatically after fault condition is removed.
-10 ~ +60 (Refer to "Derating Curve")
WORKING TEMP.
20 ~ 90% RH non-condensing
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY -20 ~ +85 , 10 ~ 95% RH
ENVIRONMENT
TEMP. COEFFICIENT
VIBRATION
0.04%/ (0 ~ 50 ) on +5V output
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
UL60950-1, TUV EN60950-1 approved
SAFETY STANDARDS
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
EMC EMISSION
EMC IMMUNITY
MTBF
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH
Compliance to EN55022 (CISPR22) Class B, EN61000-3-2,-3
Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, light industry level, criteria A
SAFETY &
EMC
(Note 4)
414.8K hrs min. MIL-HDBK-217F (25
127*76*42mm (L*W*H)
)
OTHERS
NOTE
DIMENSION
0.24Kg; 54pcs/15Kg/1.35CUFT
PACKING
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives. For guidance on how to perform these EMC tests, please refer to EMI testing of component power supplies.
(as available on http://www.meanwell.com)
5. Mounting holes M1 and M2 should be grounded for EMI purposes.
6. Heat Sink HS1,HS2 can not be shorted.
File Name:PD-65-SPEC 2011-08-18