CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
Chip Type, Higher Capacitance
High Temperature Range
PCM
High reliability, Low ESR, High ripple current.
Long life of 8000 hours at 125°C.
SMD type : Lead free reflow soldering
ꢀcondition at 260°C peak complete correspondence.
Compliant to the RoHS directive (2011/65/EU,(EU)2015/863).
ESR after Endurance at -40°C.
AEC-Q200 Qualified. Please contact us for details.
Long Life Assurance
PCR
PCM
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
–55 to +125°C
16 to 80V
Rated Capacitance Range
Capacitance Tolerance
12 to 1000µF
20% at 120Hz, 20°C
Less than or equal to the specified value 120Hz, 20°C
Tangent of loss angle (tan δ)
at
(
1)
ESR
Less than or equal to the specified value 100kHz, 20°C
at
After 2 minutes' application of rated voltage, leakage current is not more than 0.03CV or 3( ), whichever is greater.
Leakage Current ( 2)
µA
Temperature Characteristics
(Max.Impedance Ratio)
(
)
(
)
Z +125°C / Z +20°C
1.25
1.25
(100kHz)
(
)
(
)
Z –55°C / Z +20°C
Capacitance change
Within 20% of initial capacitance value ( 3)
150% or less of the initial specified value
200% or less of the initial specified value
Less than or equal to the initial specified value
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 8000 hours (φD 6.3:6000hours) at 125°C.
tan δ
Endurance
(
1)
ESR
=
Leakage current ( 2)
After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
Shelf Life
(
1)
ESR after Endurance
Less than or equal to the specified value at 100kHz, -40°C
Capacitance change
Within 20% of initial capacitance value ( 3)
150% or less of the initial specified value
200% or less of the initial specified value
Less than or equal to the initial specified value
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 85°C, 85% RH.
Damp Heat
tan δ
(
1)
ESR
(Steady State)
Leakage current ( 2)
After soldering the capacitor under the soldering conditions prescribed
here, the capacitor shall meet the specifications listed at right.
Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.
The duration for over +230°C temperature at capacitor surface shall not
exceed 60 seconds.
In case peak temperature is 260°C or less, reflow soldering shall be two
times maximum.
Capacitance change
Within 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
tan δ
Resistance to
Soldering Heat
(
1)
ESR
Leakage current ( 2)
Measurement for solder temperature profile shall be made at the
capacitor top.
Marking
Navy blue print on the case top
※ I : Leakage Current(µA), C : Rated Capacitance(µF), V : Rated Voltage(V)
1 ESR should be measured at both of the terminal ends closest where the terminals
protrude through the plastic platform.
Type numbering system (Example : 35V 150µF)
2
Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of
applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C.
1
2
3
4
5
6
7
8
9 10 11 12 13 14
P C M 1 V 1 5 1 M C L 1 G S
3 Initial value : The value before test of examination of resistance to soldering.
Taping code
Size code
Dimensions
Positive
Configuration
Standard
Plastic platform
Capacitance
Capacitance tolerance ( 20ꢀ%
Size
Code
L
Lot No.
C
0.ꢀ
0.3 max.
Rated capacitance
(
150µF
%
%
Standard
Rated voltage
(35V
Vibration
※
Please ask for
Resistance
Part Number.
Series name
Type
φ6.3×8L(φ6.3×8L),φ8×10L(φ8×10.5L),φ10×10L(φ10×10.5L),φ10×12.7L(φ10×13.2L) :
The vibration structure-resistant product is also available upon request, please ask for details.
(
) : Size of the vibration structure-resistant product.
φ6.3
:
L
0.3
0.5
Voltage (V:35V)
Series
(mm)
(mm)
Negative
Positive
H
Vibration Resistance
Standard
φ8,10
:
L
φ6.3
×
6L φ6.3
×
8L φ8
×
7L φ8
×
10L φ8
×
12L φ10
×
8L φ10
×
10L φ10
×
12.7L
φ6.3×8L φ8
×
10.5L φ10
×
10.5L φ10
×
13.2L
Size
Size
φD
L
Vibration Resistance
Capacitance
Lot No.
6.3 6.3 8.0 8.0 8.0 10.0 10.0 10.0
5.9 7.9 6.9 9.9 11.9 7.9 9.9 12.6
7.3 7.3 9.0 9.0 9.0 11.0 11.0 11.0
6.6 6.6 8.3 8.3 8.3 10.3 10.3 10.3
6.6 6.6 8.3 8.3 8.3 10.3 10.3 10.3
2.1 2.1 3.2 3.2 3.2 4.6 4.6 4.6
0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1
φD 6.3
8.0 10.0 10.0
Plastic platform
L
A
B
C
E
H
7.5 10.0 10.0 12.7
C
0.ꢀ
0.3 max.
7.3
6.6
6.6
2.5
9.0 11.0 11.0
8.3 10.3 10.3
8.3 10.3 10.3
A
B
C
3.1
4.6
4.6
E
0.5 to 0.8 1.1 to 1.5 1.1 to 1.5 1.1 to 1.5
H
L
0.5
Frequency coefficient of rated ripple current
Frequency 120Hz 1kHz 10kHz 100kHz or more
H
Voltage
Negative
Voltage (V:35V)
Series
V
16 20 25 35 50 63 80
Aid electrode
Code
C
D
E
V
H
J
K
Coefficient 0.05 0.30 0.70
1.00
Dimension table in next page.
CAT.8100M
5秒后页面跳转
英伟达新AI芯片Rubin或提前半年亮相
苹果iPhone 17将全系采用三星/LG显示LTPO OLED面板
三星深化印度制造布局，供应链本地化进程加速
芯擎科技“星辰一号”自动驾驶芯片点亮成功，2025年量产在即
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
