®
OP4005B
•
•
•
•
Quartz SAW Stabilized Differential Output Technology
Very Low Jitter Fundamental-Mode Operation at 622.08 MHz
Voltage Tunable for Phase Locked Loop Applications
Timing Reference for Optical Data Communications Systems
622.08 MHz
Optical
Timing Clock
The OP4005B is a voltage-controlled SAW clock (VCSC) designed for phase-locked loop (PLL) applications
in optical data communications systems. The differential outputs of the OP4005B are generated by high-Q,
fundamental mode quartz surface acoustic wave (SAW) technology. This technique provides very low output
jitter and phase noise, plus excellent immunity to power supply noise. The OP4005B differential outputs fea-
ture ±1% symmetry, and can be DC-configured to drive a wide range of high-speed logic families. The
OP4005B is packaged in a hermetic metal-ceramic LCC.
Absolute Maximum Ratings
Rating
Value
0 to 5.5
Units
Vdc
Vdc
°C
DC Suppy Voltage
Tune Voltage
0 to 5.5
SMC-08
Case Temperature
-55 to 100
Electrical Characteristics
Characteristic
Absolute Frequency
Tuning Range
Sym
Notes
Minimum
Typical
Maximum
Units
MHz
ppm
Vdc
622.08
Operating Frequency
f
1
2
1
O
±100
0
Tuning Voltage
3.3
±5
Tuning Linearity
Tuning Sensitivity
Modulation Bandwidth
%
1, 8
2
140
200
df/dv
300
300
1.1
ppm/V
kHz
265
Q and Q Output
V
1,3
1,3
V
Voltage into 50 W (VSWR £ 1.2)
Operating Load VSWR
Symmetry
0.60
O
P-P
2:1
55
3, 4, 5
3, 4, 6
3, 4, 6, 7
3, 6
45
%
Harmonic Spurious
Nonharmonic Spurious
@ 100 Hz offset
dBc
-30
-60
dBc
Phase Noise
-70
-100
-125
-150
0.1
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
ps
3, 6
@ 1 kHz offset
3, 6
@ 10 kHz offset
3, 6
Noise Floor
3, 4, 6, 7
3, 4, 6, 7
Q and Q Jitter
RMS Jitter (10kHz to 80MHz)
No Noise on V
12
ps
ps
CC
P-P
P-P
200 mV
Noise, from 1 MHz to ½ f on V
CC
3
12
P-P
O
8
10
KW
KW
Vdc
mA
°C
Input Impedence (Tuning Port)
Output DC Resistance (between Q & Q)
1, 3
1, 3
1, 3
1, 3
50
Operating Voltage
Operating Current
V
3.3 or 5.0
DC Power Supply
3.13
5.25
70
CC
I
CC
Operating Case Temperature
T
-40°C
+85°C
C
Lid Symbolization (YY=Year, WW=Week)
RFM OP4005B YYWW
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. COCOM CAUTION: Approval by the U.S. Department of Commerce is required
prior to export of this device.
Notes:
1. Unless otherwise noted, all specifications include the combined effects of load VSWR, V and T .
CC
C
2. Net tuning range after tuning out the effects of initial manufacturing tolerances, VSWR pushing/pulling, V , T and aging.
CC
C
3. The internal design, manufacturing processes, and specifications of this device are subject to change without notice.
4. Specified only for a balanced load with a VSWR < 1.2 ( 50 ohms each side), and a V = 3.0 Vdc.
CC
5. Symmetry is defined as the width in (% of total period) measure at 50% of the peak-to-peak voltage of either output.
6. Jitter and other noise outputs due to power supply noise or mechanical vibration are not included in this specification except where noted.
7. Applies to period jitter of either differential output. Measured with a Tektronix CSA803 signal analyzer with at least 1000 samples.
8. See Figure 4.
9. One or more of the following United States patents apply: 4, 616,197; 4,670,681; 4,760,352.
RF Monolithics, Inc.
RFM Europe
Phone: (972) 233-2903
Phone: 44 1963 251383
Fax: (972) 387-8148
Fax: 44 1963 251510
E-mail: info@rfm.com
http://www.rfm.com
OP4005B-051203
Page 1 of 7
©2001 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.