OCXO (Oven Controlled Crystal Oscillators) +5.0 V; +12 V
OC22E Series 50 ohm Load Sine Wave
MERCURY
Since 1973
Mercury OC22T is 50.8X50.8 mm 7 pin solder sealed metal pacakge with
38.1X38.1 mm pin-to-pin spacing high stability low aging OCXO. SC cut
crystal is standard for OC22 . ±0.4 ppb stability and ±150 ppb total aging
over 10 years make the OC22 ideal for base stations, digital switching,
instrumentation and frequency synthesizers. HCMOS output is available as OC22T series.
General Specifications ( 10 MHz at+25°C, at specified Vcc and +2.5 V Vcon)
Output Wave Form
Frequency Range
Sine wave. Wave form code is “E”
5.0 MHz ~20.0 MHz
AT-cut. Use “A” for crystal code or SC-cut: use “S” for crystal code.
Type of Crystal Cut Used
SC has better performance but higher cost. See technical note TN-031.
+5.0 V D.C ±5% (voltage code is “5”); +12.0 VD.C ±5% (voltage code is “12”)
±0.5 ppm max. at time of shipment; Vcon=+2.5V
Supply Voltage (Vcc)
Initial Calibration Tolerance
Best Stability
For AT crystal
For SC crystal
0°C to +60°C
±50 ppb
±0.4 ppb
-20°C to +70°C
±0.1 ppm
±5 ppb
-40°C to +85°C
±0.2 ppm
±15 ppb
Operating Temperature Range
(custom spec. on request)
Aging (after 72 hours of AT:±3 ppb max./day; ±0.5 ppm max./first year;±3 ppm max. over 10 years.
continuous operation) SC: ±0.5 ppb max./day; ±50 ppb max./first year;±150 ppb max. over 10 years.
Supply Voltage ±5% Variation
±1 ppb max.
Load ±5% variation:
±1 ppb max.
AT: 1 minute max. Within ±0.2 ppm of its reference frequency.
SC: 5 minute max. Within ±10 ppb of its reference frequency.
Warm-up time (at +25°C)
Freq. Deviation Range
AT: ±5 ppm min. ±20 ppm max.;
SC: ±0.5 ppm min, ±2 ppm max.
Referenced to fo at +25°C and over
operating temperature range.
Control Voltage Range
Transfer Function
Input Impedance
EFC Linearity
2.5 V ± 2.0 V
Positive: Increasing control voltage increases output frequency.
100 K ohms min.
±20% max.
Oven Power Dissipation
Oscillator Power Dissipation
2 Watts max. at steady-state;6 Watts max. at turn-on. At +25°C.
0.5 Watts max.
Power
Output
Output Level
Harmonic
Spurious
2 dBm typical with 50Ω load
-30 dBc min.
-75 dBc min.
Reference Voltage
Offset
+4.0 V D.C.±0.3 V D.C. or custom.
1 Hz
10 Hz
100 Hz
1 KHz
10 KHz
Phase
Noise
10 MHz AT-cut XTAL
-75 dBc
-100 dBc
-130 dBc
-140 dBc
-150 dBc
10 MHz SC-cut XTAL
-90 dBc
-120 dBc
-140 dBc
-150 dBc
-150 dBc
Storage Temperature
Shock
-55°C to +125°C
2000 G’s, 0.3 ms ½ sine
10 to 2000 Hz / 10 G’s
Vibration
MERCURY
www.mercury-crystal.com
Taiwan: TEL (886)-2-2406-2779, FAX (886)-2-2496-0769, e-mail: sales-tw@mercury-crystal.com
U.S.A.: TEL (1)-909-466-0427, FAX (1)-909-466-0762, e-mail: sales-us@mercury-crystal.com
MERCURY
Page 1 of 2
Date: July 20, 2006
Rev. 0