NTE887M
Integrated Circuit
Low Power, JFET OP Amplifier
Description:
The NTE887M is a JFET–input operational amplifier in an 8–Lead DIP type package designed as a
low–power version of the NTE857M amplifier. This device features high input impedance, wide band-
width, high slew rate, and low input offset and bias current.
Features:
D Very Low Power Consumption
D Typical Supply Current: 200µA
D Wide Common–Mode and Differential Voltage Ranges
D Low Input Bias and Offset Currents
D Common–Mode Input Voltage Range Includes VCC+
D Output Short–Circuit Protection
D High Input Impedance: JFET–Input Stage
D Internal Frequency Compensation
D Latch–Up–Free Operation
D High Slew rate: 3.5V/µs Typ
Absolute Maximum Ratings: (TA = 0° to +70°C unless otherwise specified)
Supply Voltage (Note 1), VCC+ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +18V
Supply Voltage (Note 1), VCC– . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –18V
Differential Input Voltage (Note 2), VID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±30V
Input Voltage (Note 1, Note 3), VI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±15V
Duration of Output Short Circuit (Note 4), ts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unlimited
Continuous Total Dissipation, PD
TA ≤ +25°C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 680mW
Derate Above +65°C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8mW/°C
TA = +70°C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 640mW
Operating Ambient Temperature Range, TA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0° to +70°C
Storage Temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65° to +150°C
Lead Temperature (During Soldering, 1/16” (1.6mm) from case for 10sec), TL . . . . . . . . . . . +260°C
Note 1. All voltage values, except differential voltages, are with respect to the midpoint between
VCC+ and VCC–.
Note 2. Differential voltages are at the non–inverting input pin with respect to the inverting input pin.
Note 3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage
or 15V, whchever is less.
Note 4. The output may be shorted to GND or to either supply. Temperature and/or supply voltages
must be limited to ensure that the dissipation rating is not exceeded.