NTCLE350E4
Vishay BCcomponents
www.vishay.com
NTC Thermistors, Insulated Leads for 185 °C Applications
FEATURES
• Advanced NTC ceramic technology
• Wide temperature range from -55 °C to +185 °C
• Cost efficient thermistor design
• Small body diameter of maximum 2.4 mm
• Fast response time and high sensitivity
LINKS TO ADDITIONAL RESOURCES
• Improved noxious gas and acid resistance
3
D
• Insulated Ag-plated NiFe alloy leads
• Mounting: radial
3D Models
Design Tools
Related
Documents
• AEC-Q200 qualified (rev. D)
QUICK REFERENCE DATA
PARAMETER
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
VALUE
2.1K to 30K
1, 2, 3, 5
UNIT
Resistance value at 25 °C
Tolerance on R25-value
%
APPLICATIONS
B
25/85-value
3435 to 3984
K
NTCLE350 can be processed by potting or molding into
sensors for electric traction motors, for example in the
sensing and protection of high current connectors.
Tolerance on B25/85-value
0.5 to
1
%
Operating temperature range
-55 to +185
°C
NTCLE350 is suitable for EGR applications (exhaust gas
recirculation) for steady state temperatures going up to
185 °C.
Response time (63.2 %) in stirred air
6
s
25 °C to 85 °C (for information only)
Dissipation factor in still air
(for information only)
1.0
mW/K
mW
This series is also intended for oil temperatures sensors
(OTS), in for example transmission systems and liquid
cooled starter/generator systems.
Maximum power dissipation at 55 °C
100
Minimum dielectric withstanding
voltage (RMS) between terminals
and coated body
1000
VAC
The AEC-Q200 qualification (between -55 °C and 185 °C)
enables this series to be used for classical motor thermal
sensing applications (engine coolant, fuel sensor, TMAP for
manifold air pressure) as well as in HVAC applications.
Minimum insulation resistance
between terminals and coated
body at 500 VDC
100M
30
Weight
mg
DESCRIPTION
These negative temperature coefficient thermistors consist
of a mini-chip soldered between two AWG #32 PEEK
insulated silver plated NiFe alloy leads and coated with
black colored epoxy lacquer. High adhesive strength
between PEEK wire and encapsulating lacquer.
DESIGN-IN SUPPORT
Not intended for fluid immersed applications or continuous
contact with water or conducting liquids. See also
Environmental Conditions. Can be potted in suitable resins.
For complete curve computation, please visit:
MOUNTING
www.vishay.com/thermistors/ntc-curve-list/
Important mounting and handling instructions: see
www.vishay.com/doc?29222
Consult Vishay for specific applications, mounting,
alternative RT curves, or wire length.
ELECTRICAL DATA AND ORDERING INFORMATION
SAP MATERIAL AND ORDERING NUMBER (1)
RoHS COMPLIANT
R25
R25-TOL.
ꢀ)
B25/85
(K)
B25/85-TOL.
ꢀ)
()
(
(
2100
5000
1, 2, 3, 5
1, 2, 3, 5
1, 2, 3, 5
1, 2, 3, 5
1, 2, 3, 5
3511
3435
3984
3435
3935
1
NTCLE350E4212xMB0
1
0.5
1
NTCLE350E4502xLB0
10 000
10 000
30 000
NTCLE350E4103xHB0
NTCLE350E4103xLB0
1
NTCLE350E4303xHB0
Note
(1)
Replace the x-digit by J for R25-tolerance of 5 %, H for 3 %, G for 2 %, and F for 1 %
Revision: 16-Oct-2020
Document Number: 29218
1
For technical questions, contact: nlr@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000