NCV7321
Stand-alone LIN Transceiver
Description
The NCV7321 is a fully featured local interconnect network (LIN)
transceiver designed to interface between a LIN protocol controller
and the physical bus. The transceiver is implemented in I3T
technology enabling both high−voltage analog circuitry and digital
functionality to co−exist on the same chip.
www.onsemi.com
MARKING
The NCV7321 LIN device is a member of the in−vehicle
networking (IVN) transceiver family.
DIAGRAMS
The LIN bus is designed to communicate low rate data from control
devices such as door locks, mirrors, car seats, and sunroofs at the
lowest possible cost. The bus is designed to eliminate as much wiring
as possible and is implemented using a single wire in each node. Each
node has a slave MCU−state machine that recognizes and translates
the instructions specific to that function. The main attraction of the
LIN bus is that all the functions are not time critical and usually relate
to passenger comfort.
8
NV7321−x
FALYW
G
SOIC−8
CASE 751
8
1
1
1
NV73
21−y
ALYWG
G
DFN8
CASE 506BW
1
Features
SOIC−8:
x
• LIN−Bus Transceiver
= Specific Device Code
0 = NCV7321D10
1 = NCV7321D11
2 = NCV7321D12
♦ LIN Compliant to Specification Revision 2.x (Backwards
Compatible to Version 1.3) and J2602
♦ Bus Voltage $45 V
♦ Transmission Rate 1 kbps to 20 kbps
♦ Supports K−Line Bus Architecture
• Protection
DFN8:
y
= Specific Device Code
2 = NCV7321MW2
= Fab Location Code
= (NCV7321D11R2G only)
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
F
♦ Thermal Shutdown
A
L
Y
W
G
♦ Indefinite Short−Circuit Protection on Pins LIN and WAKE
Towards Supply and Ground
♦ Load Dump Protection (45 V)
♦ Bus Pins Protected Against Transients in an Automotive
Environment
(Note: Microdot may be in either location)
• EMI Compatibility
♦ Integrated Slope Control
PIN CONNECTIONS
• Modes
1
2
3
4
8
7
6
5
RxD
EN
INH
♦ Normal Mode: LIN Transceiver Enabled, Communication via the
LIN Bus is Possible, INH Switch is On
V
BB
♦ Sleep Mode: LIN Transceiver Disabled, the Consumption from
WAKE
TxD
LIN
V
BB
is Minimized, INH Switch is Off
GND
♦ Standby Mode: Transition Mode reached either after Power−up or
after a Wake−up Event, INH Switch is on
SOIC−8 (Top View)
♦ Wake−up Bringing the Component from Sleep Mode into Standby
Mode is Possible either by LIN Command or a Digital Signal on
WAKE Pin (e.g. External Switch)
RxD
EN
1
2
3
4
8 INH
V
BB
7
6
5
EP
Quality
WAKE
TxD
LIN
• NCV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Require− ments; AEC−Q100
Qualified and PPAP Capable
GND
DFN8 (Top View)
• These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
ORDERING INFORMATION
See detailed ordering and shipping information in the package
Compliant
dimensions section on page 12 of this data sheet.
© Semiconductor Components Industries, LLC, 2015
1
Publication Order Number:
July, 2015 − Rev. 13
NCV7321/D