www.martekpower.com
NB100S & NB100D
100 Watts Output Power
SINGLE AND DUAL OUTPUTS
FEATURES
•
•
•
•
•
•
•
•
•
.38 Inch Profile
Synchronization
Remote Turn On (TTL)
Output Voltage Trim Pin
Over Temperature Protection
Output Overvoltage/Overcurrent Protection
Built-In Test (Output Power Good; Main Output)
100% Environmental Screening (Military Version)
Outputs Isolated Allowing Any Combination of
Output Voltages
How to Order:
NB 100 D I / 5 / 15 - A - D
Output Voltages:
Options:
Series
One number is for A- pins out side of unit
single out or two B- pins out bottom of unit
numbers for dual C- pins out top of unit
output. Maximum D- through hole inserts
SELECTION CHART
Output Voltage and Output Current
Total Output Power
Single (S), Dual (D) Output
Industrial (I) or Military (M)
Model Numbering Example:
current as stated
in selection chart.
(STD threaded)
I - M2.5 inserts
Single
Dual
Nominal Output
Output
Per Channel
To order a 100 watt, 15 V out (single output), industrial grade power supply with pins out the side,
the model number would be: NB100SI/15-A. Military grade would be NB100SM/15-A. To order a
100 watt, dual output, 15 V and 15 V, industrial grade power supply with pins out the top, the model
number would be NB100DI/15/15-C. Dual output, 12 V and 15 V, military grade, would be
NB100DM/12/15-C. When ordering a dual output unit, the first output voltage in the model number
is located on channel 1, and the second output voltage in the model number is located on channel
2 (see case drawing for details).
Voltage
2
Current (Amps)
Current (Amps)
20
20
10
10
3.3
5
20
10
5.2
12
19.2
8.3
6.7
4.2
3.6
9.6
4.2
3.3
2.1
1.8
INPUT CHARACTERISTICS
15
PER CHANNEL
24
28
Min.
14
Typ.
28
12
2
Max.
40
Units
Vdc
Vdc
Watt
mc
%
Input Voltage
Brown Out (75% of Full Load) [fig. I]*
No Load Power Dissipation
Inrush Charge [fig. VII]*
OUTPUT CHARACTERISTICS
4
2
PER CHANNEL
Reflective Ripple Current [fig. VIII]*
Logic Disable Current (Sink)
Logic Disable Power In
15
100
1.2
55
Min.
Typ.
Max.
Units
% Vout
mV
150
2.5
μA
✝
Set Point Accuracy
Load Regulation
Line Regulation
1
5
5
0.2%1
0.2%1
150
W
Input Ripple Rejection (120 Hz)
Input Ripple Rejection (800 Hz)
Efficiency up to
dB
mV
45
dB
Ripple P-P (10 MHz) (2V-24) [fig. IV]*
Ripple P-P (10 MHz) (28V)[fig. IV]*
45
.2%
mV
83
%
out
1%
% V
% V
See Page 21 [fig. II, III]*
Trim Range
100
out
110
EMI: Units conform to MIL-STD-461D (on the input leads) with companion filter
Remote Sense Compensation
0.5
Vdc
Input Transient: Units conform to MIL-STD-704D for transients up to 50V for 0.1 second
Overvoltage Protection(2V, 3.3V)
Overvoltage Protection (5V-28)
Current Sharing
140
125
±10
out
% V
% V
out
out
% I
STABILITY
Transient Response (Vout 1%) Time/Overshoot [fig. V & VI]*
50 dB
180°
20-80% Load
350/300
300/350
250/300
0.01
μS/mV
μS/mV
μS/mV
%/°C
Low Line - High Line
50-100% Load
Temperature Drift
0.05
0.02
150
75
0°
Long Term Drift
0.01
0 dB
%/1KHrs
Current Limit
105
25
125
out
% I
% I
Short Circuit Current
Turn On Time [fig. XI]*
Logic Turn On Time [fig. IX]*
out
1.5
1.5
mS
mS
Phase
Gain
✝
1% or 50mV, whichever is greater
-50 dB
100HZ
-180°
* figures on page 21 represents per channel
1KhZ
10KH
FREQUENCY
100KHZ
1
.2% or 25mv whichever is greater
All specifications are typical @+25°C with nominal input voltage under full output load conditions, unless otherwise noted. Specifications subject to change without notice.
>> 14
1111 Knox Street Torrance CA 90502 USA Tel: +1 310 202 8820 sales@martekpower.com