Philips Semiconductors FAST Products
Product specification
Octal shift/count registered transceiver
with adder and parity (3–State)
FAST 74F807
input and the STATOUT output is terminal
count. In this mode the CI/SI/CE input must
be high to enable the count function. The
register contents are incremented by one.
FEATURES
this device only on the output states.
Both OE pins are enabled low.
• High speed parallel registers with
positive edge–triggered D–type
flip–flops
All operating modes, other than clear,
3–State, and the two hold modes re-
quire the rising edge of the clock. All
setup and hold times must be observed
for proper functioning.
4. Count w/count enable (hold) –– same as
above except no incrementing occurs.
• High speed full adder
• 8–bit parity generator
• High impedance PNP inputs for light
bus loading
5. Count wo/count enable –– same as num-
ber 3 except the CI/SI/CE input has no con-
trol over counting or holding.
6. Shift –– The CI/SI/CE input now becomes
the serial input and the STATOUT output
becomes the serial output. In this mode the
CI/SI/CE input is shifted into the Q0 register,
Q0 into the Q1 register etc. The Q7 register
is shifted into the STATOUT.
Data on the internal register can be
switched on either the A or B ports for
output.
• Center VCC and GND pins and con-
trolled output buffers minimize
ground–bounce problems
Depeding on the state of the select in-
puts (S0, S1, S2), and carry in/ serial in/
clock enable (CI/SI/CE), the 74F807 has
nine distinct operating modes:
• 3–State glitch–free power–up and
power–down
7. Load A inputs –– The CI/SI/CE input has
no bearing in either of the load modes. The
STATOUT output becomes the parity out.
The parity out is high for an odd number of
registered bits high, and low for even number
of registered bits high (even parity). In this
mode the An inputs are loaded into the
internal register and output to the B bus. If
OEA = low the internal register would wrap
around and be loaded again.
• Broadside pinout
1. Add mode w/carry in – the CI/SI/CE
input is used as a carry in signal and the
STATOUT output is the carry out signal.
(In add mode the COUT is NOT
registered. This means the carry output
signal appears at the STATOUT output
one clock prior to the related data.). In
this mode, the CI/SI/CE input is added
to the register contents and to the
inputs. (The adder uses only the An
inputs, not the Bn inputs.)
DESCRIPTION
The 74F807 is a registered transceiver
that also has the capability to perform
count, shift, and add functions. It is also
has the capability to generate a parity
bit output. All of this is done within a
28–pin package.
8. Load B inputs –– same as number 7
except the A and B busses are switched.
9. Hold –– Again the CI/SI/CE input is not
used; the STATOUT output is still the parity
out. In this mode either the A bus, B bus or
both can be held with the registered data. No
other operation is performed.
The MR input is an overriding
asynchronous reset which forces the
STATOUT output low as well as the A
and B busses.
2. Add mode wo/carry in –– same as above
except the CI/SI/CE input is not included in
the addition.
The A and B busses have separate OE
inputs (OEA, OEB]. These inputs have
no bearing on the internal functioning of
3. Count w/count enable (count) –– the CI/SI/
CE input is now used as the count enable
TYPE
TYPICAL f
TYPICAL SUPPLY CURRENT (TOTAL)
max
74F807
115MHz
155mA
ORDERING INFORMATION
ORDER CODE
DESCRIPTION
COMMERCIAL RANGE
V
CC
= 5V ±10%, T
= 0°C to +70°C
amb
28–pin plastic DIP (300 mils)
N74F807N
N74F807D
N74F807A
1
28–pin SOL
28–pin PLCC
Note to ordering information
1.Thermal mounting techiques are recommended. See SMD Process Applications (page 17) for a discussion of thermal consideration for surface
mounted devices.
1
June 18, 1991
853–1421 02931
5秒后页面跳转
摩尔斯微电子在美国约书亚树国家公园测试 Wi-Fi HaLow
贸泽上架Tallysman TW5386智能GNSS天线
SL74HC10N：高性能三输入与非门解析
AIC1781A 电池充电控制器深度解析
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
