MT88E46
Bellcore Compliant Calling Number
Identification Circuit
Data Sheet
November 2006
Features
•
Compatible with Bellcore GR-30-CORE,
SR-
Ordering Information
TSV-002476; TIA/EIA-716 and TIA/EIA-777
Pin compatible with MT88E45
MT88E46AS
MT88E46ASR
MT88E46AS1
20 Pin SOIC
20 Pin SOIC
20 Pin SOIC*
Tubes
•
•
Tape & Reel
Tubes, Bake &
Drypack
Differential input amplifiers with adjustable gains
MT88E46ASR1
20 Pin SOIC*
Tape & Reel,
Bake & Drypack
for Tip/Ring and 4-wire side connections
•
TIA (Telecommunications Industry Association)
MEI (Multiple Extension Interworking) compatible
architecture: CAS (CPE Alerting Signal) detection
is selectable between Tip/Ring and 4-wire side
*Pb Free Matte Tin
-40 to +85 °C
•
Computer Telephony Integrated (CTI) systems
•
4-wire side CAS detection is Bellcore talkoff and
talkdown compliant when near end speech is
attenuated 8 dB or better, and is close to talkoff
compliant even without near end speech attenuation
Description
The MT88E46 is a CMOS integrated circuit suitable for
receiving the FSK and CAS signals in North American
(Bellcore) CIDCW, CWD and CID (Calling Identity
Delivery) services. It provides an optimal solution for the
CIDCW (also known as Type 2) and CWD (Type 2.5)
telephone set applications by providing separate input op-
amps for Tip/Ring and 4-wire side (receive pair of the
telephone hybrid or speech IC) connections. The Tip/Ring
connection is compatible with TIA’s MEI scheme and can
be used for FSK demodulation and ‘on hook mode’ CAS
detection. The 4-wire side connection is for ‘off hook
mode’ CAS detection. The CAS detection modes - on
hook and off hook - use different algorithms which are
optimized for the CPE states. In ‘off hook mode’ the CAS
detector is Bellcore compliant when near end speech is
attenuated 8dB or better. ‘On hook mode’ is optimized for
talkdown only and typically meets talkdown condition 1
(the average case) without speech attenuation at Tip/Ring
such as in the on hook state MEI CPE.
•
•
•
Tip/Ring side CAS detection typically meets
talkdown condition 1 (the average case)
1200 baud Bell 202 and CCITT V.23 FSK
demodulation
Selectable 3-wire FSK data interface (serial bit
stream or 1 byte buffer) with facility to monitor stop
bit for framing error check
FSK carrier detect status output
3 to 5 V ± 10% supply voltage
Uses 3.579545 MHz crystal
•
•
•
•
Low power CMOS with power down mode
Applications
•
Bellcore compliant CIDCW (Calling Identity
Delivery on Call Waiting) and CWD (Call Waiting
Deluxe) telephones
•
CIDCW and CWD telephone adjunct boxes
MODE
GS1
GS1en
DATA
DCLK
FSK
FSK
Data Timing
Recovery
+
-
IN1+
IN1-
Bandpass
Demod
Anti-Alias
Filter
GS1en
PWDN
FSKen
CASen
Carrier
IN2+
IN2-
+
-
CD
Detector
PWDN
DR
2130Hz
DR/DET
Bandpass
Tone
Detection
Algorithm
GS2
PWDN
CASen
DET
MODE
GS1en
FSKen
Bias
VREF
2750Hz
Generator
Bandpass
Control Bit
Decode
PWDN
Vdd
Vss
CASen
Oscillator
On/Off Hook mode
Patent pending
OSC1 OSC2
CB0 CB1 CB2
Figure 1 - Functional Block Diagram
Zarlink Semiconductor Inc.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright 2000-2006, Zarlink Semiconductor Inc. All Rights Reserved.