ML600RUSeries
Ultra-Compact, 6W
Wide 4:1 Input, SMT
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Conditions
24 VDC Input
Min.
9.0
Typ.
24
48
Max.
36.0
75.0
9.0
Units
Key Features:
• 6W Output Power
• Ultra-Compact SMT Case
• Wide 4:1 Input
Input Voltage Range
Start Up Voltage
VDC
48 VDC Input 18.0
24 VDC Input
48 VDC Input
VDC
18.0
• 1,500 VDC Isolation
24 VDC Input
48 VDC Input 17.0
8.5
Under Voltage Shutdown
VDC
mW
• Single & Dual Outputs
Short Circuit Input Power
Input Filter
Output
Parameter
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
3,000
• -40ºC to +80ºC Operation
• 16 Standard Models
ꢀ (Pi) Filter - Meets EN 55022 Class A
Conditions
At 50% Load
Dual Output, Balanced Loads
For VIN = Min to Max
For IOUT = 15% to 100%
See Note 1
Min.
Typ.
1.0
1.0
0.5
0.5
60
300
3
0.01
150
Max.
2.0
Units
%
• Tight Line/Load Regulation
• Available on Tape/Reel
1.0
1.2
100
600
%
%
mV P - P
µS
%
%/ºC
%
Load Regulation
Ripple & Noise (20 MHz)
Transient Response Time, See Note 2
Transient Response Deviation
Temperature Coefficient
Overload Protection
Output Short Circuit
General
25% Load Step Change
0.02
Foldback Type
Continuous (Autorecovery)
110
Parameter
Isolation Voltage
Conditions
Min.
60 Seconds 1,500
500 VDC 1,000
100 kHz, 1V
Typ.
Max.
Units
VDC
M
pF
kHz
Isolation Resistance
Isolation Capacitance
Switching Frequency
Remote On/Off (See Note 3)
Parameter
Supply On
Supply Off
Standby Input Current
Control Common
1,200 1,500
330
Conditions
Min.
2.5
-0.7
Typ.
Max.
50.0
0.8
Units
VDC
VDC
mA
10
Referenced to Negative Input (pin 2)
Environmental
Parameter
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Cooling
Conditions
Min.
-40
Typ.
Max.
+80
+105
+125
Units
ºC
ºC
Ambient
Case
-50
ºC
Free Air Convection
RH, Non-condensing
Humidity
95
%
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Physical
Case Size
Case Material
Weight
0.87 x 0.80 x 0.40 Inches (22.0 x 20.3 x 10.2 mm)
Molding (UL94-V0)
0.27 Oz (7.8g)
Reliability Specifications
Parameter
Conditions
Min.
Typ.
Max.
Units
T: (781) 344-8226
F: (781) 344-8481
MTBF
MIL HDBK 217F, 25ºC, Gnd Benign
350
kHours
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Moisture Sensitivity Level (MSL)
Absolute Maximum Ratings
Parameter
IPC/JEDEC J-STD-020D Level 2
Conditions
Min.
Typ.
Max.
50.0
100.0
260
Units
VDC
ºC
24 VDC Input -0.7
48 VDC Input -0.7
Input Voltage Surge (1 Sec)
Lead Temperature
1.5 mm From Case For 10 Sec.
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com