MIC3001
Micrel
MIC3001
SFP Management IC with Internal Calibration
General Description
Features
The MIC3001 enables the implementation of sophisticated,
hot-pluggable fiber optic transceivers with intelligent laser
control and an internally calibrated Digital Diagnostic Moni-
toring Interface per SFF-8472. It essentially integrates all
non-datapath functions of an SFP transceiver into a tiny
4mm × 4mm MLF™ package. It also works well as a
microcontroller peripheral in transponders or 10Gbps trans-
ceivers.
• APC or constant-current laser bias
• Turbo mode for APC loop start-up and shorter laser turn
on time
• Supports multiple laser types and bias circuit topologies
• Drives external low-cost BJT for laser bias
• Integrated digital temperature sensor
• Temperature compensation of modulation, bias, and
fault levels via NVRAM look-up tables
• Direct interface to SY88932, SY88982, SY89307 and
other drivers
• NVRAM to support GBIC/SFP serial ID function
• User writable EEPROM scratchpad
• Diagnostic monitoring interface per SFF-8472
– Monitors and reports critical parameters:
temperature, bias current, TX and RX optical power,
and supply voltage
A highly configurable automatic power control (APC) circuit
controls laser bias. Bias and modulation are temperature
compensated using dual DACs, an on-chip temperature
sensor, and NVRAM look-up tables. A programmable inter-
nalfeedbackresistorprovidesunprecedenteddynamicrange
for APC. Controlled laser turn-on facilitates hot-plugging.
An analog-to-digital converter converts the measured tem-
perature, voltage, bias current, transmit power, and received
power from analog to digital. An EEPOT provides frontend
adjustmentofRXpower.Eachparameteriscomparedagainst
user-programmed warning and alarm thresholds. Analog
comparators and DACs provide high-speed monitoring of
received power and critical laser operating parameters. Data
can be reported as either internally calibrated or externally
calibrated.
– S/W control and monitoring of TXFAULT, RXLOS,
RATESELECT, and TXDISABLE
– Internal or external calibration
– EEPOT for adjusting RX power measurement
• Power-on hour meter
• Interrupt capability
• Extensive test and calibration features
2
• 2-wire I C compatible serial interface
Aninterruptoutput,power-onhourmeter,anddata-readybits
add user friendliness beyond SFF-8472. The interrupt output
and data-ready bits reduce overhead in the host system. The
power-on hour meter logs operating hours using an internal
real-time clock and stores the result in NVRAM.
• SFP MSA and SFF-8472 compliant
• 3.0V to 3.6V power supply range
• 5V-tolerant I/O
• 4mm × 4mm 24-pin MLF™ package
Applications
• SFF/SFP optical transceivers
• SONET/SDH transceivers and transponders
• Fibre channel transceivers
• 10Gbps transceivers
• Free space optical communications
• Proprietary optical links
Communication with the MIC3001 is via an industry standard
2-wire serial interface. Nonvolatile memory is provided for
serial ID, configuration, and separate OEM and user
scratchpad spaces. Two-level password protection guards
against data corruption.
Ordering Information
Part Number
Junction Temp. Range
Package
MIC3001BML
–45°C to +105°C
24-pin MLF™
MicroLeadFrame and MLF are trademarks of Amkor Technology, Inc.
Micrel, Inc. • 1849 Fortune Drive • San Jose, CA 95131 • USA • tel + 1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
August 2004
1
M9999-082404