Series
MD100MHI
Miniature, 1W SIP
Medical Approved
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Key Features:
• 1W Output Power
Conditions
Min.
Typ.
5.0
Max.
5.5
Units
5 VDC Input
4.5
Input Voltage Range
VDC
• 3 kVAC rms Isolation
12 VDC Input 10.8
LC Filter
12.0
13.2
Input Filter
• Reinforced Insulation
• Miniature SIP Case
• Single & Dual Outputs
• 12 Standard Models
• 2.0 MH MTBF
• Industry Standard Pin-Out
• EN 60950 Approved
• EN 60601 Approved
Reverse Polarity Input Current
0.3
A
Output
Parameter
Conditions
Min.
Typ.
1.0
0.1
1.2
Max.
3.0
Units
%
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
Dual Output , Balanced Loads
For Vin Change of 1%
1.0
%
1.5
%
Load Regulation, See Note 1
Ripple & Noise (20 MHz), See Note 2
Ripple & Noise (20 MHz)
Ripple & Noise (20 MHz)
Temperature Coefficient
Output Short Circuit
General
See Model Selection Guide
100
0.01
Typ.
150
200
15
mV P - P
mV P - P
mV rms
%/°C
Over Line, Load & Temp.
0.02
Momentary (0.5 Sec.)
Parameter
Conditions
Min.
Max.
Units
VAC rms
VPk
Isolation Voltage
60 Seconds 3,000
Isolation Test Voltage
Isolation Resistance
Isolation Capacitance
Switching Frequency
Environmental
Parameter
Flash Tested for 1 Sec 4,500
500 VDC
10
G
100 kHz, 1V
15
80
20
pF
50
100
kHz
Conditions
Min.
Typ.
Max.
+85
Units
°C
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Cooling
Ambient -25
Case
+90
°C
-50
+125
°C
Free Air Convection
Humidity
RH, Non-condensing
95
%
Physical
Case Size
0.87 x 0.30 x 0.49 Inches (22.0 x 7.5 x 12.5 mm)
Non-Conductive Black Plastic (UL94-V0)
0.13 Oz (3.9g)
Case Material
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Weight
Reliability Specifications
Parameter
Conditions
Min.
Typ.
Max.
Units
MTBF
MIL HDBK 217F, 25°C, Gnd Benign
2.0
MHours
Safety Approvals
Absolute Maximum Ratings
Parameter
UL 60601, UL 60950, EN 60601, EN 60950
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Conditions
Min.
5 VDC Input -0.7
12 VDC Input -0.7
Typ.
Max.
9.0
Units
Input Voltage Surge (1 Sec)
VDC
29.0
260
650
Lead Temperature
1.5 mm From Case For 10 Sec
All Models
°C
Internal Power Dissipation
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com