Document Number: MC33813
Rev. 12, 12/2019
NXP Semiconductors
Data sheet: Technical Data
One cylinder small engine control IC
33813
Powered by SMARTMOS technology, the 33813 delivers a cost-optimized IC
solution for managing one-cylinder engines. With five drivers, two pre-drivers, a
5.0 V regulator for the MCU, a protected external sensor supply and a high level of
integration, the IC offers an ideal response to contemporary market requirements.
The innovative VRS system optimizes noise immunity under cranking conditions.
Diagnostic and protection features present on all outputs allow applications to
operate with greater safety.
ONE CYLINDER SMALL ENGINE
CONTROL IC
Features:
• Operates over supply voltage range of 4.5 V < VPWR < 36 V
• Start-up/shut-down control and power sequence logic with KEYSW input
• MCU supply: VCC is a 5.0 V ( 2.0%, 200 mA) regulated supply
• Sensor supply: VPROT (100 mA) is a VCC tracking protected sensor supply
• Two configurable pre-drivers for IGBT or general purpose gate MOSFETs for
ignition and O2 sensor (HEGO) heater:
98ASA00737D
AE SUFFIX (PB-FREE)
48-PIN LQFP-EP
• PWM
• Overcurrent shutdown
• Short-to-battery shutdown
Applications:
• Five low-side drivers with full diagnostics, self-protection and PWM control:
• One fuel injector drivers, RDS(on) = 0.6 Ω, ILIMIT = 1.8 A, to drive typical 12 Ω
high-impedance injectors
Small engine control for:
• Motor scooters
• Small motorcycles
• Lawn mowers
• Lawn trimmers
• Snow blowers
• Chain saws
• Gasoline-driven electrical generators
• Outboard motors
• Relay 1 driver, RDS(on) = 0.4 Ω, ILIMIT = 3.0 A, to drive fuel pump
• Relay 2 driver, RDS(on) = 1.5 Ω, ILIMIT = 1.2 A, to drive power relay
• Lamp driver, RDS(on) = 1.5 Ω, ILIMIT = 1.2 A, to drive warning lamp or an LED
• Programmable Tachometer Driver, RDS(on) = 20 Ω, Ishutdown = 60 mA, to drive
a Tachometer display
• Innovative configurable VRS conditioning circuit, with two different parameter
settings for engine cranking and running mode and an optional automatic mode
to improve noise immunity in cranking conditions
• K-line (ISO9141)
• MCU reset generator and programmable watchdog
• MCU Interface: 16-bit SPI and parallel interface with 5.0 V IO capability
.
MC33813
V
BAT
5.0 V Sensor Supply
Keyswitch
BAT
V
BAT
V
KEYSW
VPROT
Relay 2
(Power)
ROUT2
MIL
VPWR
LAMPOUT
ROUT1
TACHOUT
VPPREF
Relay 1
(Fuel Pump)
VPPSENS
TACHOMETER
O2HFB
O2HOUT
O2HSENSP
O2 Heater
MCU
VCC
VCC
+5.0 V
RESETB
RESETB
O2HSENSN
INJOUT1
V
BAT
4
SPI
SPI
Injectors
MRX
MTX
BATSW
RIN1
RIN2
IGNIN1
GPIO
GPIO
GPIO
GPIO
GPIO
GPIO
V
BAT
ISO9141
ISO9141
IGNFB1
IGNOUT1
GPIO
INJIN1
VRSOUT
O2HIN
VRSP
VRSN
GND
GPIO
GPIO
IGNSENSP
IGNSENSN
Crankshaft VRS
Figure 1. 33813 simplified application diagram
© NXP B.V. 2019.