SEMICONDUCTOR TECHNICAL DATA
The MC10H113 is a Quad Exclusive OR Gate with an enable common to all
four gates. The outputs may be wire–ORed together to perform a 4–bit
comparison function (A = B). The enable is active LOW.
L SUFFIX
CERAMIC PACKAGE
CASE 620–10
•
•
•
Propagation Delay, 1.3 ns Typical
Power Dissipation 175 mW Typ/Pkg (No Load)
Improved Noise Margin 150 mV (Over Operating Voltage and
Temperature Range)
P SUFFIX
PLASTIC PACKAGE
CASE 648–08
•
•
Voltage Compensated
MECL 10K–Compatible
FN SUFFIX
PLCC
CASE 775–02
MAXIMUM RATINGS
Characteristic
Symbol
Rating
Unit
Vdc
Vdc
mA
Power Supply (V
= 0)
V
EE
–8.0 to 0
CC
Input Voltage (V
= 0)
V
I
0 to V
CC
EE
LOGIC DIAGRAM
Output Current— Continuous
— Surge
I
out
50
100
E
9
Operating Temperature Range
T
A
0 to +75
°C
4
5
Storage Temperature Range— Plastic
— Ceramic
T
–55 to +150
–55 to +165
°C
°C
stg
TRUTH TABLE
2
3
IN
E
L
OUTPUT
L
L
L
L
ELECTRICAL CHARACTERISTICS (V
0°
= –5.2 V ±5%) (See Note)
EE
H
L
H
25°
75°
H
H
X
L
H
X
L
L
H
L
L
6
7
Characteristic
Symbol Min
Max
Min
Max
Min
Max
Unit
H
Power Supply Current
I
E
—
46
—
42
—
46
mA
Input Current High
Pins 5, 7, 11, 13
Pins 4, 6, 10, 12
Pin 9
I
µA
inH
—
—
—
430
510
1100
—
—
—
270
320
740
—
—
—
270
320
740
10
11
14
15
V
V
V
= PIN 1
= PIN 16
= PIN 8
CC1
CC2
EE
Input Current Low
High Output Voltage
Low Output Voltage
High Input Voltage
Low Input Voltage
I
0.5
—
0.5
—
0.3
—
µA
inL
V
–1.02 –0.84 –0.98 –0.81 –0.92 –0.735 Vdc
–1.95 –1.63 –1.95 –1.63 –1.95 –1.60 Vdc
–1.17 –0.84 –1.13 –0.81 –1.07 –0.735 Vdc
–1.95 –1.48 –1.95 –1.48 –1.95 –1.45 Vdc
OH
12
13
V
OL
V
IH
V
IL
AC PARAMETERS
DIP
Propagation Delay
Data
Enable
t
pd
ns
PIN ASSIGNMENT
0.4
0.5
1.7
2.3
0.4
0.5
1.8
2.4
0.5
0.6
1.9
2.5
V
A
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
CC2
CC1
Rise Time
Fall Time
NOTE:
t
0.5
0.5
1.8
1.8
0.6
0.6
1.9
1.9
0.6
0.6
2.0
2.0
ns
ns
r
D
C
D
D
C
C
t
OUT
OUT
IN
OUT
OUT
f
B
Each MECL 10H series circuit has been designed to meet the dc specifications shown in the test table,
after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed
circuit board and transverse air flow greater than 500 Iinear fpm is maintained. Outputs are terminated
through a 50–ohm resistor to –2.0 volts.
A
IN
A
IN
IN
B
IN
IN
BIN
IN
ENABLE
V
EE
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–11 of the Motorola MECL Data
Book (DL122/D).
9/96
Motorola, Inc. 1996
REV 6
2–213