MBR30200CT
Features
• Low Power Loss, High Efficiency
• Guardring for Overvoltage Protection
• Low Forward Voltage Drop And High Frequency Operation
• Lead Free Finish/RoHS Compliant(Note 1) ("P" Suffix Designates
Compliant. See Ordering Information)
• Halogen Free Available Upon Request By Adding Suffix "-HF"
• Epoxy Meets UL 94 V-0 Flammability Rating
30 Amp
Schottky Barrier
Rectifier
200 Volts
Maximum Ratings
• Operating Junction Temperature Range: -55°C to +150°C
• Storage Temperature Range: -55°C to +150°C
• Mounting Torgue: 5 in-lbs Maximum
• Typical Thermal Resistance Per Leg : 1.7°C/W Junction to Case
TO-220AB
Maximum
Maximum
Recurrent
Peak Reverse
Voltage
Maximum
RMS
Voltage
DC
MCC
Device
C
B
F
Blocking
Voltage
Part Number
Marking
S
Q
T
MBR30200CT MBR30200CT
200V
140V
200V
A
U
Electrical Characteristics @ 25°C Unless Otherwise Specified
ꢁ
ꢀ
ꢂ
30A
15A
Maximum Average
Forward Rectified Current
H
IF(AV)
(See Fig.1)
K
Peak Forward Surge Current
200A
1.0A
8.3ms,Half Sine
tp = 2.0us, 1KHz
IFSM
IRRM
D
R
Peak Repetitive Reverse
Current Per Leg
J
L
G
V
N
Voltage Rate of
Change (Rated VR)
10,000V/us
dv/dt
DIMENSIONS
INCHES MM
MIN MAX MIN MAX
DIM
NOTE
IF=15A,TJ=25⁰C
IF=15A,TJ=125⁰C
IF=30A,TJ=25⁰C
IF=30A,TJ=125⁰C
0.95V
0.75V
0.99V
0.86V
A
B
C
D
F
G
H
J
0.560 0.625 14.22 15.88
0.380 0.429 9.65 10.90
0.140 0.201 3.56 5.10
0.020 0.045 0.51 1.14
0.131 0.170 3.34 4.31
0.079 0.121 2.01 3.07
----- 0.250 ----- 6.35
0.011 0.025 0.28 0.64
0.500 0.580 12.70 14.73
0.045 0.060 1.14 1.52
0.158 0.242 4.02 6.14
0.087 0.135 2.22 3.43
0.080 0.126 2.04 3.19
0.045 0.055 1.14 1.39
0.230 0.270 5.84 6.86
----- 0.050 ----- 1.27
Maximum Instantaneous
Forward Voltage Per Leg
(Note 5)
VF
Φ
Maximum Reverse Current
Per Leg at Working Peak
Reverse Voltage
TJ=25⁰C
0.1mA
1.0mA
IR
TJ=125⁰C
K
L
RMS Isolation Voltage (MBRF
Type Only) from Terminals
to Heatsink With t = 1.0
Second, RH≤30%
( Note 2)
( Note 3)
( Note 4)
4500V
3500V
1500V
N
Q
R
S
T
VI
SOL
Note :1. High Temperature Solder Exemption Applied, see EU Directive Annex 7.
2. Clip mounting (on case), where lead does not overlap heatsink with 0.110" offset
3. Clip mounting (on case), where leads do overlap heatsink
U
V
0.045 ----- 1.15
-----
4. Screw mounting with 4-40 screw, where washer diameter is < 4.9 mm (0.19")
5. Pulse test: 300us pulse width, 1% duty cycle
Internal Structure
PIN 1
PIN 2
PIN 3
Case
Rev.3-2-12012020
1/3
MCCSEMI.COM