MB1500MRWRI4
EN 60601 Approved
Compact, 2:1 Input, 15W
DC/DC Converters
Electrical Specifications
Key Features:
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
• EN 60601 3RD Ed. Approved
• 15W Output Power
• 4.2 kVrms Isolation
• Reinforced Insulation
• 2 x MOPP per EN 60601-1
3RD Edition & ANSI/AAMI
ES 60601-1
Input
Parameter
Conditions
12 VDC Input
Min.
Typ.
Max.
9.0
Units
Input Start Voltage
24 VDC Input
48 VDC Input
12 VDC Input
24 VDC Input
48 VDC Input
18.0
36.0
VDC
7.5
15.0
33.0
Under Voltage Shutdown
VDC
mS
Input Filter
Start Up Time
(Pi) Filter
Nominal VIN, Constant, Resistive Load
30
• 5 µA Max Leakage Current
• Wide 2:1 Input Range
• Compact 1 x 2 In Case
• Single & Dual Outputs
• 1.42 MH MTBF
Output
Parameter
Conditions
Min.
Typ.
Max.
1.0
2.0
0.5
0.5
Units
%
%
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
Dual Output , Balanced Loads
VIN = Min to Max
Single Output
%
Load Regulation, IOUT = 0% to 100%
%
Dual Output
1.0
5V Output
50
Ripple & Noise (20 MHz), See Note 2
12V, 15V, 12V, 15V Output
24V Output
100
150
150
mV P - P
Output Power Protection
Transient Recovery Time, See Note 3
Transient Response Deviation
Temperature Coefficient
Output Short Circuit
General
Hiccup Circuit
%
µSec
%
300
5.0
0.02
25% Load Step Change
3.0
%/ºC
Continuous (Autorecovery)
Parameter
Conditions
Min.
60 Seconds 4,200
300 Vrms
Typ.
Max.
Units
Vrms
Isolation Voltage, Rated
Reinforced Insulation Working Voltage
Leakage Current
Isolation Resistance
Isolation Capacitance
Switching Frequency
Environmental
Parameter
240 VAC, 60 Hz
500 VDC
5
µA
G⍀
pF
10
100 kHz, 1V
80
285
kHz
Conditions
Min.
Typ.
Max.
Units
Operating Temperature Range
Cooling
See Table on Page 3
Free Air Convection
Humidity
Altitude
RH, Non-condensing
95
4,000
%
m
Physical
Case Size
See Mechanical Diagram (Page 4)
Case Material
Weight
Reliability Specifications
Parameter
Non-Conductive Black Plastic (UL94-V0)
1.06 Oz (30g)
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Conditions
MIL HDBK 217F, 25ºC, Gnd Benign 1.42
IEC/EN 60601-1, EN 60601-1 3RD Edition, 2xMOPP
Min.
Typ.
Max.
Units
MHours
MTBF
Safety Standards
ANSI/AAMI ES 60601-1 2xMOPP Recognition, (UL Certificate)
ANSI/AAMI ES 60601-1, CAN/CSA-C22.2 No.60601-1
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Absolute Maximum Ratings
Parameter
Conditions
12 VDC Input
Min.
Typ.
Max.
25.0
50.0
100.0
260
Units
VDC
ºC
Input Voltage Surge (0.1 Sec)
24 VDC Input
48 VDC Input
Lead Temperature
1.5 mm From Case For 10 Sec
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com