5秒后页面跳转
MAX4223EVKIT-SO PDF预览

MAX4223EVKIT-SO

更新时间: 2024-11-21 02:52:11
品牌 Logo 应用领域
美信 - MAXIM /
页数 文件大小 规格书
4页 55K
描述
Optional Adjustable Gain

MAX4223EVKIT-SO 数据手册

 浏览型号MAX4223EVKIT-SO的Datasheet PDF文件第2页浏览型号MAX4223EVKIT-SO的Datasheet PDF文件第3页浏览型号MAX4223EVKIT-SO的Datasheet PDF文件第4页 
19-1281; Rev 0; 8/97  
MAX4 2 2 3 Eva lu a t io n Kit  
Evluates:3/MAX24  
_______________Ge n e ra l De s c rip t io n  
____________________________Fe a t u re s  
1GHz -3dB Bandwidth  
The MAX4223 evaluation kit (EV kit) simplifies evalua-  
tion of the 1GHz, low-power MAX4223 current-feed-  
back amplifier. The EV kit circuit demonstrates the  
MAX4223 in the noninverting unity-gain configuration.  
RF-style connectors (SMA) and 50terminating resis-  
tors are included for test equipment compatibility.  
300MHz 0.1dB Gain Flatness  
1100V/µs Slew Rate  
±5V Supply Operation  
The MAX4223 EV kit uses a PC board design optimized  
for high-frequency amplifiers. This board can also be  
used to evaluate the MAX4224 and other Maxim ampli-  
fiers that share the same pinout .  
Optional Adjustable Gain  
High-Impedance Shutdown Mode  
Fully Assembled and Tested  
______________Ord e rin g In fo rm a t io n  
____________________Co m p o n e n t Lis t  
DESIGNATION QTY  
DESCRIPTION  
PART  
TEMP. RANGE  
BOARD TYPE  
C1, C2  
2
0.1µF, 10% ceramic capacitors  
MAX4223EVKIT-SO  
-40°C to +85°C  
Surface Mount  
10µF, 10V, 20% tantalum capacitors  
AVX TAJB106M010 or  
Note: To evaluate the MAX4224, request a MAX4224ESA free  
sample.  
C3, C4  
2
Sprague 293D106X0010B  
R1, R2  
RF  
2
1
0
2
1
1
1
1
1
49.9, 1% resistors  
560, 5% resistor  
Open  
_________________________Qu ic k S t a rt  
The MAX4223 EV kit is fully assembled and tested.  
Follow these steps to verify board operation.  
RG  
IN, OUT  
U1  
SMA connectors  
MAX4223ESA  
3-pin header  
1) The circuit requires supply voltages of ±2.85V to  
±5.5V. For evaluation purposes, connect a +5V sup-  
ply to the pad labeled VCC and a -5V supply to the  
pad labeled VEE. Connect the power-supply ground  
to the pad labeled GND.  
JU1  
None  
None  
None  
Shunt for JU1  
PC board  
MAX4223 data sheet  
2) Verify that the shunt is across pins 1 and 2 of jumper  
JU1.  
3) Connect the output labeled OUT to an oscilloscope  
input. For best performance, terminate the output  
with a 50load.  
______________Co m p o n e n t S u p p lie rs  
4) Turn on the power supply. Apply a signal of ±2.5V  
maximum to the SMA connector labeled IN.  
SUPPLIER  
AVX  
Sprague  
PHONE  
FAX  
(803) 946-0690  
(603) 224-1961  
(803) 626-3123  
(603) 224-1430  
5) Verify the output signal on the oscilloscope.  
Note: When using a 50-terminated oscilloscope input,  
the output amplitude observed will be half that of the  
input, due to the voltage divider formed by the 49.9Ω  
back-terminating resistor (R1) and the oscilloscope  
input termination impedance.  
Note: Please indicate that you are using the MAX4223 when  
contacting these component suppliers.  
________________________________________________________________ Maxim Integrated Products  
1
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800.  
For small orders, phone 408-737-7600 ext. 3468.  

与MAX4223EVKIT-SO相关器件

型号 品牌 获取价格 描述 数据表
MAX4223-MAX4228 MAXIM

获取价格

1GHz Low-Power SOT23 Current-Feedback Amplifier with Shutdown
MAX4224 MAXIM

获取价格

1GHz, Low-Power, SOT23, Current-Feedback Amplifiers with Shutdown
MAX4224 ADI

获取价格

1GHz、低功耗、SOT23封装、电流反馈放大器,带有关断
MAX4224ESA MAXIM

获取价格

1GHz, Low-Power, SOT23, Current-Feedback Amplifiers with Shutdown
MAX4224ESA+ MAXIM

获取价格

暂无描述
MAX4224EUT+T MAXIM

获取价格

Operational Amplifier, 1 Func, 6000uV Offset-Max, PDSO6, SOT-23, 6 PIN
MAX4224EUT-T MAXIM

获取价格

1GHz, Low-Power, SOT23, Current-Feedback Amplifiers with Shutdown
MAX4225 MAXIM

获取价格

1GHz, Low-Power, SOT23, Current-Feedback Amplifiers with Shutdown
MAX4225 ADI

获取价格

1GHz、低功耗、SOT23封装、电流反馈放大器,带有关断
MAX4225ESA MAXIM

获取价格

1GHz, Low-Power, SOT23, Current-Feedback Amplifiers with Shutdown