MAX3223E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS707–JANUARY 2006
FEATURES
DB, DW, OR PW PACKAGE
•
ESD Protection for RS-232 Bus Pins
(TOP VIEW)
– ±15-kV Human-Body Model (HBM)
EN
C1+
1
2
3
4
5
6
7
8
9
10
20 FORCEOFF
– ±8-kV IEC61000-4-2, Contact Discharge
– ±15-kV IEC61000-4-2, Air-Gap Discharge
19
18
17
16
15
14
13
12
11
V
CC
V+
C1−
C2+
C2−
GND
DOUT1
RIN1
ROUT1
FORCEON
DIN1
•
Meets or Exceeds the Requirements of
TIA/EIA-232-F and ITU v.28 Standards
•
•
•
•
•
•
•
Operates With 3-V to 5.5-V VCC Supply
Operates up to 500 kbit/s
V−
DOUT2
RIN2
ROUT2
Two Drivers and Two Receivers
Low Standby Current . . . 1 µA Typ
External Capacitors . . . 4 × 0.1 µF
Accepts 5-V Logic Input With 3.3-V Supply
DIN2
INVALID
RHL PACKAGE
(TOP VIEW)
Alternative High-Speed Pin-Compatible Device
(1 Mbit/s) for SNx5C3223E
APPLICATIONS
•
•
•
•
•
•
Battery-Powered Systems
PDAs
Notebooks
Laptops
Palmtop PCs
Hand-Held Equipment
1
24
C1+
NC
V+
C1–
C2+
V
CC
2
23
22
21
20
19
18
17
16
15
14
NC
3
4
GND
DOUT1
RIN1
ROUT1
FORCEON
DIN1
5
6
DESCRIPTION/ORDERING INFORMATION
7
C2–
V–
The MAX3223E consists of two line drivers, two line
receivers, and a dual charge-pump circuit with ±15-kV
ESD protection pin to pin (serial-port connection pins,
including GND). The device meets the requirements
of TIA/EIA-232-F and provides the electrical interface
between an asynchronous communication controller
and the serial-port connector. The charge pump and
four small external capacitors allow operation from a
single 3-V to 5.5-V supply. The device operates at
typical data signaling rates up to 500 kbit/s and a
maximum of 30-V/µs driver output slew rate.
8
9
DOUT2
NC
RIN2
10
11
NC
DIN2
12
13
NC − No internal connection
Flexible control options for power management are available when the serial port is inactive. The
auto-powerdown feature functions when FORCEON is low and FORCEOFF is high. During this mode of
operation, if the device does not sense a valid RS-232 signal, the driver outputs are disabled. If FORCEOFF is
set low and EN is high, both drivers and receivers are shut off, and the supply current is reduced to 1 mA.
Disconnecting the serial port or turning off the peripheral drivers causes auto-powerdown to occur.
Auto-powerdown can be disabled when FORCEON and FORCEOFF are high. With auto-powerdown enabled,
the device is activated automatically when a valid signal is applied to any receiver input. The INVALID output is
used to notify the user if an RS-232 signal is present at any receiver input. INVALID is high (valid data) if any
receiver input voltage is greater than 2.7 V or less than –2.7 V, or has been between –0.3 V and 0.3 V for less
than 30 µs. INVALID is low (invalid data) if the receiver input voltage is between –0.3 V and 0.3 V for more than
30 µs. Refer to Figure 4 for receiver input levels.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Copyright © 2006, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.