Sample &
Buy
Support &
Community
Product
Folder
Tools &
Software
Technical
Documents
LP5521
SNVS441I –JANUARY 2007–REVISED NOVEMBER 2016
LP5521 Three-Channel RGB, White-LED Driver With Internal Program Memory and
Integrated Charge Pump
1 Features
3 Description
The LP5521 is a three-channel LED driver designed
to produce variety of lighting effects for mobile
devices. A high-efficiency charge pump enables LED
driving over full Li-Ion battery voltage range. The
device has a program memory for creating variety of
lighting sequences. When program memory has been
loaded, LP5521 can operate autonomously without
processor control allowing power savings.
1
•
Adaptive Charge Pump With 1× and 1.5× Gain
Provides Up to 95% LED Drive Efficiency
•
Charge Pump with Soft Start and Overcurrent,
Short-Circuit Protection
•
•
Low Input Ripple and EMI
Very Small Solution Size, No Inductor or Resistors
Required
The device maintains excellent efficiency over a wide
operating range by automatically selecting proper
charge pump gain based on LED forward voltage
requirements and is able to automatically enter
power-save mode, when LED outputs are not active
and thus lowering current consumption.
•
•
•
•
200-nA Typical Shutdown Current
Automatic Power Save Mode
I2C-Compatible Interface
Independently Programmable Constant Current
Outputs with 8-Bit Current Setting and 8-Bit PWM
Control
Three independent LED channels have accurate
programmable current sources and PWM control.
Each channel has program memory for creating
desired lighting sequences with PWM control.
•
•
Typical LED Output Saturation Voltage 50 mV and
Current Matching 1%
Three Program Execution Engines with Flexible
Instruction Set
The LP5521 has a flexible digital interface. Trigger
I/O and a 32-kHz clock input allow synchronization
between multiple devices. Interrupt output can be
used to notify processor, when LED sequence has
ended. The LP5521 has four pin selectable I2C-
compatible addresses. This allows connecting up to
four parallel devices in one I2C-compatible bus. GPO
and INT pins can be used as a digital control pin for
other devices.
•
•
•
Autonomous Operation Without External Control
Large SRAM Program Memory
Two General Purpose Digital Outputs
2 Applications
•
•
•
•
•
•
•
•
Fun and Indicator Lights
LCD Sub-Display Backlighting
Keypad RGB Backlighting and Phone Cosmetics
Vibra, Speakers, Waveform Generator
Blood Glucose Meter
The LP5521 requires only four small, low-cost
ceramic capacitors.
Comprehensive application tools are available,
including command compiler for easy LED sequence
programming.
Handheld POS Terminals
Electronic Access Control
Device Information(1)
Where RGB Indication is Needed
PART NUMBER
LP5521TM
PACKAGE
DSBGA (20)
WQFN (24)
BODY SIZE
Typical Application Circuit
2.093 mm × 1.733 mm (MAX)
5.00 mm × 4.00 mm (NOM)
CFLY1
CFLY2
LP5521YQ
0.47 µF
0.47 µF
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
COUT
1 µF
CFLY1P
VDD
CFLY1N
CFLY2P
CFLY2N
VOUT
CIN
-
1 µF
RGB LED 0...25.5 mA/LED
SCL
SDA
R
G
B
LP5521
EN
MCU
CLK_32K
INT
TRIG
GPO
ADDR_SEL0
ADDR_SEL1
GNDs
Copyright © 2016, Texas Instruments Incorporated
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.