5秒后页面跳转
LNDINA333C PDF预览

LNDINA333C

更新时间: 2024-10-19 12:25:07
品牌 Logo 应用领域
LINEAR_DIMENSIONS 仪表放大器
页数 文件大小 规格书
2页 176K
描述
INA333 Footprint Compatible Instrumentation Amplifiers (INA) use 50% Less Current

LNDINA333C 数据手册

 浏览型号LNDINA333C的Datasheet PDF文件第2页 
ADVANCE DATASHEET  
LNDINA333A/B/C  
INA333 Footprint Compatible Instrumentation  
Amplifiers (INA) use 50% Less Current  
GENERAL DESCRIPTION  
FEATURES  
The LNDINA333A/B/C are precision instrumentation  
amplifiers designed to be footprint compatible with the TI  
INA333. Although the LNDINA333 are footprint compatible  
they offer similar performance to the INA333 with a 30%  
reduction in power consumption (25uA typical and 30uA  
maximum vs. 50uA typical and 80uA maximum for the  
INA333). The LNDINA333A has a single ended output  
replicating the INA333A while the outputs of LNDINA333B/C  
are fully differential.  
Instrumentation Amplifier  
Single ended (LNDINA333A)  
Fully differential (LNDINA333B)  
Fully differential AC only (LNDINA333C)  
+2.7V to +5.5V input range  
25μA typ current consumption (INA333, 50μA)  
35μA typ current (LNDINA333C)  
350kHz typical bandwidth  
25μV typical input offset voltage  
100dB typical CMRR  
100nV/√Hz typical input referred noise  
RFI Filtered Inputs  
External resistor or programmable gain  
Minimum gain setting 100V/V  
Input range: GND-0.1V to VDD+0.1V  
Output range: GND+0.05V to VDD-0.05V  
Low drift: 2μV/°C typical  
+/-5pA typical input bias current  
10mA short circuit current  
8kV ESD Protection (vs. 4kV for INA333)  
Temperature range: -40°C to 125°C  
Footprint compatible with EPAD DFN-8  
If an RG resistor is connected between the RG pins then the  
differential current will be set by the external resistor. On the  
other hand if the RG inputs remain high impedance then a  
pulse on RG/DIG- will cause an internal resistor to decrement  
in value, while a pulse on RG/DIG+ will cause the internal  
resistor to increment in value. Default is half scale.  
The LNDINA333C is an AC only instrumentation amplifier  
which has a 5Hz 3dB high pass response. Integrators are  
connected between the output and feedback nodes to form a  
high pass response as shown in the block diagram below.  
The LNDINA333A/B/C features 8kV HBM ESD protection  
compared to 4kV with the INA333. The inputs are also RFI  
filtered to reduce EMI susceptibility.  
The LNDINA333A/B/C is available in a EPAD DFN-8 package  
which has a 65°C/W thermal resistance.  
APPLICATIONS  
Portable heart rate equipment  
Portable fitness & wellness products  
Non-critical diagnostics  
Vibration measurement equipment  
Instrumentation  
Bridge amplifiers  
Pressure sensors  
Weigh scales  
Sensor amplifiers  
BLOCK DIAGRAM  
PACKAGE  
RG/DIG+  
RG/DIG-  
INM  
VDD  
INP  
VOUT/VOP  
REF/VOM  
GND  
Figure 1 LNDINA333C Equivalent Block Diagram  
Linear Dimensions Semiconductor Inc. 22620 Ricardo Rd, Cupertino CA 95014 USA tel 312.321.1810 fax 312.321.1830 www.lineardimensions.com   

与LNDINA333C相关器件

型号 品牌 获取价格 描述 数据表
LND-MA32 LINEAR_DIMENSIONS

获取价格

32 Channel High Voltage Amplifier
LND-OP28 LINEAR_DIMENSIONS

获取价格

Dual 5A, 44V, BiCMOS Operational Amplifiers
LND-PA21 LINEAR_DIMENSIONS

获取价格

Dual 5 Amp 40 V Power Operational Amplifiers
LND-SA55 LINEAR_DIMENSIONS

获取价格

Pulse Width Modulated Amplifier
LNDSP16-3A LINEAR_DIMENSIONS

获取价格

Portable Three Terminal Heart Rate Monitor
LNDSP17 LINEAR_DIMENSIONS

获取价格

Complete Physiological Monitoring System & Fusion Development Kit
LND-SP64HV LINEAR_DIMENSIONS

获取价格

32MHZ, 64 CHANNEL SERIAL TO PARALLEL CONVERTER WITH PUSH-PULL OUTPUTS
LND-W-152 INFINEON

获取价格

AC-DC Regulated Power Supply Module, 2 Output
LND-X-152 INFINEON

获取价格

AC-DC Regulated Power Supply Module, 2 Output
LND-Y-152 INFINEON

获取价格

AC-DC Regulated Power Supply Module, 2 Output