5秒后页面跳转
LM5119_1 PDF预览

LM5119_1

更新时间: 2024-09-29 11:36:39
品牌 Logo 应用领域
美国国家半导体 - NSC /
页数 文件大小 规格书
10页 1076K
描述
Evaluation Board Input Voltage Range: 14V to 55V

LM5119_1 数据手册

 浏览型号LM5119_1的Datasheet PDF文件第2页浏览型号LM5119_1的Datasheet PDF文件第3页浏览型号LM5119_1的Datasheet PDF文件第4页浏览型号LM5119_1的Datasheet PDF文件第5页浏览型号LM5119_1的Datasheet PDF文件第6页浏览型号LM5119_1的Datasheet PDF文件第7页 
National Semiconductor  
Application Note 2065  
Eric Lee  
LM5119 Evaluation Board  
September 28, 2010  
choose the correct connector and wire size when attaching  
the source power supply and the load.  
Introduction  
The LM5119EVAL evaluation board provides the design en-  
gineer with a fully functional dual output buck converter, em-  
ploying the LM5119 Dual Emulated Current Mode Syn-  
chronous Buck Controller. The evaluation board is designed  
to provide both 10V and 5V outputs over an input range of  
14V to 55V. Also the evaluation board can be easily config-  
ured for a single 10V, 8A regulator.  
SOURCE POWER  
The power supply and cabling must present low impedance  
to the evaluation board. Insufficient cabling or a high  
impedance power supply will droop during power supply ap-  
plication with the evaluation board inrush current. If large  
enough, this droop will cause a chattering condition during  
power up. During power down, insufficient cabling or a high  
impedance power supply will overshoot. This overshoot will  
cause a non-monotonic decay on the output.  
Performance of the Evaluation  
Board  
An additional external bulk input capacitor may be required  
unless the output voltage droop/overshoot of the source pow-  
er is less than 0.7V. In this board design, UVLO setting is  
conservative while UVLO hysteresis setting is aggressive.  
Minimum input voltage can goes down with an aggressive  
design. Minimum operating input voltage depends on the out-  
put voltage droop/overshoot of the source power supply and  
the forced off-time of the LM5119. Refer to the LM5119  
datasheet for complete design information.  
Input Voltage Range: 14V to 55V  
Output Voltage: 10V (CH1), 5V (CH2)  
Output Current: 4A (CH1), 8A (CH2)  
Nominal Switching Frequency: 230 KHz  
Synchronous Buck Operation: Yes  
Diode Emulation Mode: Yes  
Hiccup Mode Overload Protection: Yes  
External VCC Sourcing: Yes  
LOADING  
When using an electronic load, it is strongly recommended to  
power up the evaluation board at light load and then slowly  
increase the load. If it is desired to power up the evaluation  
board at maximum load, resistor banks must be used. In gen-  
eral, electronic loads are best suited for monitoring steady  
state waveforms.  
Powering and Loading  
Consideration  
When applying power to the LM5119 evaluation board, cer-  
tain precautions need to be followed. A misconnection can  
damage the assembly.  
AIR FLOW  
PROPER BOARD CONNECTION  
Prolonged operation with high input voltage at full power will  
cause the MOSFETs to overheat. A fan with a minimum of  
200LFM should be always provided.  
The input connections are made to the J1 (VIN) and J2 (RTN/  
GND) connectors. The CH1 load is connected to the J3  
(OUT1+) and J4 (OUT1-/GND) and the CH2 load is connect-  
ed to the J6 (OUT2+) and J5 (OUT2-/GND). Be sure to  
30126006  
FIGURE 1. Typical Evaluation Setup  
© 2010 National Semiconductor Corporation  
301260  
www.national.com  

与LM5119_1相关器件

型号 品牌 获取价格 描述 数据表
LM5119PSQ NSC

获取价格

Wide Input Range Dual Synchronous Buck Controller
LM5119PSQ/NOPB TI

获取价格

5.5V 至 65V 宽输入电压、电流模式双路同步降压控制器 | RTV | 32 | -
LM5119PSQE NSC

获取价格

Wide Input Range Dual Synchronous Buck Controller
LM5119PSQE/NOPB TI

获取价格

5.5V 至 65V 宽输入电压、电流模式双路同步降压控制器 | RTV | 32 | -
LM5119PSQX NSC

获取价格

Wide Input Range Dual Synchronous Buck Controller
LM5119PSQX/NOPB TI

获取价格

5.5V 至 65V 宽输入电压、电流模式双路同步降压控制器 | RTV | 32 | -
LM5119Q TI

获取价格

汽车级 5.5V 至 65V 宽输入电压、电流模式双路同步降压控制器
LM5119QPSQ/NOPB TI

获取价格

汽车级 5.5V 至 65V 宽输入电压、电流模式双路同步降压控制器 | RTV | 32
LM5119QPSQX/NOPB TI

获取价格

汽车级 5.5V 至 65V 宽输入电压、电流模式双路同步降压控制器 | RTV | 32
LM5121 TI

获取价格

Wide Input Synchronous Boost Controller with Disconnection Switch Control