5秒后页面跳转
LM1292N PDF预览

LM1292N

更新时间: 2024-11-11 22:51:59
品牌 Logo 应用领域
美国国家半导体 - NSC /
页数 文件大小 规格书
10页 221K
描述
Video PLL System for Continuous-Sync Monitors

LM1292N 数据手册

 浏览型号LM1292N的Datasheet PDF文件第2页浏览型号LM1292N的Datasheet PDF文件第3页浏览型号LM1292N的Datasheet PDF文件第4页浏览型号LM1292N的Datasheet PDF文件第5页浏览型号LM1292N的Datasheet PDF文件第6页浏览型号LM1292N的Datasheet PDF文件第7页 
April 1999  
LM1292  
Video PLL System for Continuous-Sync Monitors  
General Description  
Features  
n Wide continuous autosync range — 22 kHz–125 kHz  
(1:5.7) with no component switching or external  
adjustments  
The LM1292 is a very low jitter, integrated horizontal time  
base solution specifically designed to operate in high perfor-  
mance, continuous-sync video monitors. It automatically  
synchronizes to any H frequency from 22 kHz to 125 kHz  
and provides the drive pulse to the high power deflection cir-  
cuit.  
n No manufacturing trims required — internal VCO  
capacitor trimmed on chip  
n No costly high-precision components needed  
n Very low phase jitter (below 800 ps at 125 kHz)  
n DC controlled H phase and duty cycle  
n Video mute pulse for blanking during H frequency  
transitions  
Available sync processing includes a vertical sync separator  
and a composite video sync stripper. An internal sync selec-  
tion scheme gives highest priority to separate H and V sync,  
then composite sync, and finally sync on video; no external  
switching between sync sources is necessary. The LM1292  
provides polarity-normalized H/HV and V sync outputs.  
n Input sync prioritization  
n Clamp pulse position and width control  
n Continuous clamp pulse output, even with no sync input  
n Resistor-programmable minimum and maximum VCO  
frequency  
n X-ray input disables H drive and mutes video until VCC  
powered down  
n H drive disabled for VCC 9.5V  
n Horizontal output transistor protected against accidental  
turn-on during flyback  
The  
LM1292  
design  
uses  
an  
on-chip  
FVC  
(Frequency-to-Voltage Converter) to set the center fre-  
quency of the VCO (Voltage-Controlled Oscillator). This  
technique allows autosync operation over the entire fre-  
quency range using just one optimized set of external com-  
ponents.  
<
The system includes a second phase detector which com-  
pensates for storage time variation in the horizontal output  
transistor; the picture’s horizontal position is thus indepen-  
dent of temperature and component variance.  
n Capacitor-programmable frequency ramping, df vco/dt,  
protects H output transistor during scanning mode  
changes  
The LM1292 provides DC control pins for H Drive duty cycle  
and flyback phase.  
Connection Diagram  
DS012844-1  
FIGURE 1. Order Number LM1292N  
See NS Package Number N28B  
© 1999 National Semiconductor Corporation  
DS012844  
www.national.com  

与LM1292N相关器件

型号 品牌 获取价格 描述 数据表
LM1295 NSC

获取价格

DC Controlled Geometry Correction System for Continuous Sync Monitors
LM1295N NSC

获取价格

DC Controlled Geometry Correction System for Continuous Sync Monitors
LM1296 NSC

获取价格

Raster Geometry Correction System for Multi-Frequency Displays
LM1296N NSC

获取价格

Raster Geometry Correction System for Multi-Frequency Displays
LM129AGMW8 FAIRCHILD

获取价格

IC 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 6.9 V, UUC, WAFER, Voltage Reference
LM129AH Linear

获取价格

6.9V Precision Voltage Reference
LM129AH NSC

获取价格

Precision Reference
LM129AH#PBF Linear

获取价格

IC 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 6.9 V, MBCY2, LEAD FREE, METAL CAN, TO-46, 2 PIN,
LM129AH#TRPBF Linear

获取价格

IC 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 6.9 V, MBCY2, LEAD FREE, METAL CAN, TO-46, 2 PIN,
LM129AH/883 NSC

获取价格

Precision Reference