APPLICABLE STANDARD
Operating
-25C to +85C (95%RH MAX)
AC 30 V , DC 42
Storage Temperature
Range
-10C to +60 C (95%RH MAX)
RATING Temperature Range
Voltage
V
Wire size
MAX AWG#26
Current
2
A
Applicable Cable
φ7.3±0.2
SPECIFICATIONS
ITEM
TEST METHOD
REQUIREMENTS
QT AT
CONSTRUCTION
X
X
X
X
General examination
Examined visually and with a measuring instrument.
Confirmed visually.
According to the drawing.
Marking
ELECTRICAL CHARACTERISTICS
X
X
X
X
Contact resistance
Measured at
1
A MAX (DC or 1 000 Hz).
15 m MAX.
Insulation resistance
100 V DC.
1000 M MIN.
X
X
Voltage proof
300 V AC. For 1 min.
No flashover or breakdown.
MECHANICAL CHARACTERISTICS
Insertion force
Extraction force
N MAX.
N MIN.
Contact Insertion and Extraction
Measured with a φ
steel gauge.
-
-
-
-
-
-
forces
-
X
Connector Mating and Unmating
Measured with an applicable connector.
Without locking device
Mating force 50 N MAX.
Unmating force 50 N MAX.
Forces
X
Mechanical Operation
Vibration
Mated and unmated 1000 times.
1) Contact resistance: 30 m MAX.
X
2) No damage, cracks or looseness of parts.
Frequency: 10 → 55 → 10 Hz, Single Amplitude 0.75 mm,
5min/cycle, for 10 cycles in each of three mutually perpedicular
directions.
1) No electrical discontinuity of more than10 s.
2) No damage, cracks or looseness of parts.
X
X
-
-
Acceleration: 490 m/s2
Shock
Half sine wave pulses of 11 ms.
Performed 3 times in each of three mutually perpendicular
directions.
Breaking Strength
Applied to the cable in up, down, left and right directions while
mated.
No breakage .35N MAX
3
2
X
X
-
-
ENVIRONMENTAL CHARACTERISTICS
Damp Heat
Subjected to 40゚C, at a humidity of 90〜95% for 96h.
1) Insulation resistance: 10 MΩ MIN (At high humidity).
2) insulation resistance: 100 MΩ MIN (When dry).
3) No damage, crack or looseness of parts.
1) insulation resistance: 100 MΩ MIN.
(Steady State)
Rapid Change of Temperature
Temperature: -55→ R/T(1) → +85 → R/T ℃
Time: 30 → 2 to 3 → 30 → 2 to 3 min for 5 cycles.
Subjected to 5% salt spray for 48h.
X
-
2) No damage, cracks or looseness of parts.
No heavy corrosion which impairs functionality.
Corrosion Salt Mist
Heat Resistance
X
X
X
X
-
-
-
-
Subjected to + 85 ℃ for 96 h.
Subjected to - 55 ℃ for 96 h.
No damage, cracks or looseness of parts.
No damage, cracks or looseness of parts.
No deformation or excessive looseness of terminals.
Cold Resistance
Resistance to Soldering Heat
Soldering iron is placed to the soldering surface for 5±1s. (Iron
tip temperature +350±10℃).
Solderability
Soldered at solder temperature, +350±10℃ for immersion
duration, 2 to 3 s.
The solder shall have wetted the soldering surface and
there shall be no small lumps of solder.
X
-
Sealing(2)
Subjected to a depth of 1.8m for 48h.
No water penetration into the connector.
X
X
-
Air tightness(2)
17.6 kPa of air pressure applied to the inside of the mated
connector for 30s.
No air bubbles emitted from the inside of the
Connector.
-
COUNT
DESCRIPTION OF REVISIONS
DESIGNED
KN.IKEHARA
CHECKED
EJ.KUNII
DATE
1
DIS-C-00001974
18.01.24
17.06.14
17.06.14
17.06.14
17.06.14
△
3
REMARKS
APPROVED
CHECKED
DESIGNED
DRAWN
YH.YAMADA
EJ.KUNII
NOTES
(1) R/T:Room Temperature
(2) Sealing and Air Tightness shall be tested in mated condition with an applicable connector.
KN.IKEHARA
KN.IKEHARA
Unless otherwise specified, refer to IEC 60512(JIS C 5402).
Note QT:Qualification Test AT:Assurance Test X:Applicable Test
ELC-377501-00-00
DRAWING NO.
PART NO.
CODE NO.
LF10WBLPA-12P
SPECIFICATION SHEET
1
HIROSE ELECTRIC CO., LTD.
3
△
1/1
CL136-0039-0-00
FORM HD0011-2-1