APPLICABLE STANDARD
UL approved(E52653)
OPERATING
STORAGE TEMPERATURE
RANGE
-25 C TO
+85 C
-10
C TO
-
+60 C
RATING
TEMPERATURE RANGE
VOLTAGE
AC 60 V , DC 60 V
1 A (NO.1,3,4,6)
4 A (NO.2,5)
WIRE SIZE
CURRENT
APPLICABLE CABLE
-
SPECIFICATIONS
ITEM
TEST METHOD
REQUIREMENTS
QT AT
CONSTRUCTION
GENERAL EXAMINATION
MARKING
X
X
X
VISUALLY AND BY MEASURING INSTRUMENT.
CONFIRMED VISUALLY.
ACCORDING TO DRAWING.
X
ELECTRIC CHARACTERISTICS
X
X
X
X
X
X
15 m MAX.
1000 M MIN.
CONTACT RESISTANCE
INSULATION RESISTANCE
VOLTAGE PROOF
CONTACT SHALL BE MEASURED AT DC
1
A
100
300
V DC.
V AC. FOR 1 min.
NO FLASHOVER OR BREAKDOWN.
MECHANICAL CHARACTERISTICS
CONTACT INSERTION AND
WITHDRAWAL FORCES
φ0.53±0.003 BY STEEL GAUGE.(NO.1,3,4,6)
+0.003
INSERTION AND WITHDRAWAL FORCES
0.15 N MIN.(NO.1,3,4,6)
φ0.68
BY STEEL GAUGE.(NO.2,5)
-0
X
-
0.2 N MIN.(NO.2,5)
CONNECTOR INSERTION AND
WITHDRAWAL FORCES
MECHANICAL OPERATION
VIBRATION
MEASURED BY APPLICABLE CONNECTOR.
INSERTION AND WITHDRAWAL FORCES
X
X
-
-
LOCKING DEVICE WITH UNLOCK
CONTACT RESISTANCE: 30
: 25 N MAX.
m MAX.
1000 TIMES INSERTIONS AND EXTRACTIONS.
①NO ELECTRICAL DISCONTINUITY OF 10 s.
FREQUENCY: 10 → 55 → 10 (Hz) (1CYC,5min),
X
X
-
-
SINGLE AMPLITUDE 0.75 mm, AT 10 CYC,FOR 3 DIRECTIONS. ②NO DAMAGE, CRACK AND LOOSENESS, OF PARTS.
① NO ELECTRICAL DISCONTINUITY OF 10 s.
② NO DAMAGE, CRACK AND LOOSENESS, OF PARTS.
NO BREAKAGE MAX 100N.
SHOCK
IN OPPOSITE DIRECTIONS OF EACH 3 DEMENSION AXIS FOR 3
TIMES AT 490 m/s2 DURACTIONS OF PULSE 11 ms.
MAX 100 N SHALL BE APPLIED TO CABLE IN UP AND
DOWN,LEFT AND RIGHT DIRECTIONS WHEN MATED.
BREAKING STRENGTH
X
-
ENVIRONMENTAL CHARACTERISTICS
DAMP HEAT
EXPOSED AT 40 ℃, 90 TO 95 %, 96 h.
① INSULATION RESISTANCE: 10 MΩ MIN
(AT HIGH HUMIDITY).
(STEADY STATE)
② INSULATION RESISTANCE: 100 MΩ MIN
(AT DRY).
X
-
③ NO DAMAGE.CRACK AND LOOSENESS OF PARTS.
① INSULATION RESISTANCE: 100 MΩ MIN.
RAPID CHANGE OF TEMPERATURE TEMPERATURE -55→ R/T(1) → +85 → R/T ℃
X
X
-
-
TIME 30 → 2 TO 3 → 30 → 2 TO 3 min UNDER 5 CYCLES. ② NO DAMAGE.CRACK AND LOOSENESS OF PARTS.
EXPOSED IN 5 SALT WATER SPRAY FOR 48 h.
CORROSION SALT MIST
NO MAJOR CORROSION DAMAGE TO ELECTRICAL AND
MECHANICAL FUNCTIONS(INTERMATEABILITY).
NO DAMAGE,CRACK AND LOOSENESS OF PARTS.
NO DAMAGE,CRACK AND LOOSENESS OF PARTS.
NO DEFORMATION OF CASE OF EXCESSIVE LOOSENESS
OF THE TERMINALS.
X
X
-
-
DRY HEAT
EXPOSED AT + 85 ℃,96 h.
COLD
EXPOSED AT - 55 ℃,96 h.
RESISTANCE TO SOLDERING
HEAT
SOLDER TEMPERATURE, +350±10℃, FOR IMMERSION
DURATION, 5±1 s.
X
X
-
-
SOLDERABILITY
SOLDERED AT SOLDER TEMPERATURE, +350±10℃ FOR
IMMERSION DURATION, 2 TO 3 s.
SOLDER SURFACE TO BE FREE FROM PIN-HOLE,
NO WETTING AND OTHER DEFECTS.
SEALING(2)
EXPOSED AT A DEPTH OF 1.8 m FOR 48 h.
NO WATER PENETRATION INSIDE CONNECTOR.
X
X
-
-
AIR TIGHTNESS(2)
APPLY AIR PRESSURE 17.6kPa FOR 0.5min TO INSIDE
CONNECTOR.
NO AIR BUBBLES INSIDE CONNECTOR.
COUNT
DESCRIPTION OF REVISIONS
DESIGNED
CHECKED
DATE
△
0
REMARK
APPROVED
CHECKED
DESIGNED
DRAWN
HY.KOBAYASHI
HY.KOBAYASHI
TY.SUZUKI
18.02.22
18.02.22
18.02.22
18.02.20
NOTES(1)R/T:ROOM TEMPERATURE
(2)SEALING AND AIRTIGHTNESS SHALL BE TESTED BY APPLICABLE CONNECTOR.
Unless otherwise specified, refer to IEC 60512(JIS C 5402).
HM.SAITO
Note QT:Qualification Test AT:Assurance Test X:Applicable Test
DRAWING NO.
PART NO.
ELC-119204-31-00
LF07WBRB-6SD-A(31)
SPECIFICATION SHEET
HIROSE ELECTRIC CO., LTD.
0
△
1/1
CODE NO.
CL136-1022-0-31
FORM HD0011-2-1