™
Le9502
Ringing Subscriber Line Interface Circuit
VE950 Series
ORDERING INFORMATION
APPLICATIONS
Short/Medium Loop: approximately 2000 ft. of 26 AWG,
and 5 REN loads
Package1
Packing2
Device
Le9502BTC
Tray
44-pin eTQFP (Green Package)
Voice over IP/DSL – Integrated Access Devices, Smart
Residential Gateways, Home Gateway/Router
Cable Telephony – NIU, Set-Top Box, Home Side Box,
Cable Modem, Cable PC
1. The green package meets RoHS Directive 2002/95/EC of the
European Council to minimize the environmental impact of
electrical equipment.
2. For delivery using a tape and reel packing system, add a "T" suffix
Fiber–Fiber In The Loop (FITL), Fiber to the Home
(FTTH)
to the OPN (Ordering Part Number) when placing an order.
Wireless Local Loop, Intelligent PBX, ISDN NT1/TA
DESCRIPTION
The Zarlink Le9502 Ringing Subscriber Line Interface Circuit
(RSLIC) device from the VE950 series has enhanced and
optimized features to directly address the requirements of
FEATURES
Integrated Dual-Channel Device
— Built-in boost switching power supply tracks line voltage Voice over Broadband applications. Its goal is to reduce system
minimizing power dissipation
level costs, space, and power through higher levels of
integration, and to reduce the total cost of ownership by offering
better quality of service. The Le9502 RSLIC device provides a
totally configurable solution to the BORSCHT functions for two
lines. The resulting system is less complex, smaller, and
denser, yet cost effective with minimal external components.
The Le9502 RSLIC device requires only two power supplies:
+3.3 VDC and nominally +12 VDC. The latter power supply can
range from +8 VDC to +40 VDC, depending on the application.
A single TTL-level clock source drives an external transistor
which controls the ramp voltage that in turn feeds the switching
regulators. Five programmable states are available: Active,
Reverse Polarity, Ringing, Standby, and Disconnect. The DC
feed, two-wire AC input impedance, hook-switch threshold, and
ring trip threshold are programmable via external discrete
components. Binary fault detection is provided upon
application of fault conditions or thermal overload.
— Only +3.3 V and +12 V (nominal) required
— Wide range of input voltages (+8 V to +40 V) supported
— Minimal external discrete components
— 44-pin eTQFP package
Ringing
— 70 Vpk into 5REN
— 90 Vpk capable
— Sinusoidal or trapezoidal capability
— DC offset support
— Common differential interface for both channels
World Wide programmability:
— Two-wire AC impedance
— Dual Current Limit
— Loop closure and ring trip thresholds
Five SLIC States, including:
— Low power Standby state
— Reverse Polarity
BLOCK DIAGRAM
Le9502
RELATED LITERATURE
Switching Power
Supply
081189 Le9500 RSLIC Device Data Sheet
081208 Le9501 RSLIC Device Data Sheet
080696 Le77D11 VoSLIC™ Device Data Sheet
080697 Le78D11 VoSLAC™ Device Sheet
080716 Le77D11 /Le78D11 Chip Set User’s Guide
Ring
Tip
2-wire
Tip+Ring
Interface
2-wire to 4-wire
conversion
Differential
Codec
Codec
Device
080780 Layout Considerations for the Le77D11 and
Interface
Le9502 Devices Application Note
2-wire to 4-wire
conversion
2-wire
Tip+Ring
Interface
Ring
Tip
Switching Power
Supply
Document ID# 081007 Date:
Sep 18, 2007
3
Rev:
G
Version:
Distribution:
Public Document