LDF24E-xx-xxxSeries
Miniature, SMT
ConstantCurrentOutput
DC/DC LED Drivers
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
Parameter
Key Features:
Conditions
Conditions
Min.
5.5
Typ.
24.0
Max.
48.0
55.0
Units
VDC
VDC
• 300 - 700 mA Output Current
• Constant Current Output
• Miniature SMTCase
• PWM & Analog Dimming
• Wide 5.5V to 48V Input Range
• Efficiency to 96%
Input Voltage Range
Max Input Voltage
Input Filter
Output
Parameter
Output Current Accuracy
Output Current Stability
Output Capacitive Load
Ripple & Noise
Temperature Coefficient
Output Short Circuit
Environmental
See Note 1
Internal Capacitor
Min.
Vin = 24V
Typ.
2.0
Max.
3.0
1.0
1,000
120
0.015
Units
%
%
µF
mV P-P
%/ºC
Vin = 48V
• 2.0 MHrs MTBF
• Low, Low Cost!
Continuous
Parameter
Conditions
Min.
-40
-40
Typ.
+25
+25
Max.
+85
+71
+100
+125
Units
300 mA, 350 mA Output Models
All Other Models
Case
Operating Temperature Range, Ambient
ºC
Operating Temperature Range, Case
Storage Temperature Range
Cooling
Humidity
Lead Temperature
Physical
ºC
ºC
-55
Free Air Convection
RH, Non-condensing
1.5 mm From Case For 10 Sec
95
260
%
ºC
Case Size
Case Material
Weight
0.94 x 0.54 x 0.295 Inches (23.86 x 13.70 x 7.50 mm)
Non-Conductive Black Plastic (UL94-V0)
0.212 Oz (6.0g)
Remote On/Off Control
Parameter
Conditions
Min.
Typ.
Max.
Units
DC/DC On
Open Or 2.8 VDC < 6.0 VDC
DC/DC Off
<0.6 VDC
Remote Pin Drive Current
Quiescent Input Current (Shutdown Mode)
PWM Dimming
Parameter
Vcont = 5.0 VDC
Vin = 24V, Vcont = <0.6 VDC
1
mA
µA
400
Conditions
Min.
Typ.
Max.
Units
Operation Frequency
Reliability Specifications
Parameter
0.2
10
kHz
Conditions
Min.
Typ.
Max.
Units
MTBF
MIL HDBK 217F, 25ºC, Gnd Benign
2.0
MHours
Connection Notes:
Typical Connection: DC Input
1. Input filter components (C1, L1 & C2) are
used to help meet the conducted emissions
requirements (EN 55022 B) for the unit.
Recommended values are:
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
C2 - 2.2 µF
L1 - 1.25 mH
C3 - 1.0 µF
Other components added to the circuit
include an input storage capacitor to help
prevent problems due to input line sags and
an output capacitor to improve performance.
Recommended values are:
C1 - 470 µF
C4 - 1.0 µF
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Typical Connection: AC Input
2. To comply with EN61000-4-5, a TVS should
be installed before the input filter compo-
nents. A SMCG51 is recommended.
www.micropowerdirect.com