ꢀ ꢁ ꢂꢃ ꢄ ꢀꢁ ꢂꢃ ꢅ
ꢆ ꢇꢈꢅꢉ ꢇꢊꢀ ꢋ ꢌꢈꢀ ꢍ ꢎꢌ ꢅ ꢉꢏ ꢐ ꢋꢉ ꢑ
SLRS008C − SEPTEMBER 1986 − REVISED NOVEMBER 2004
L293 . . . N OR NE PACKAGE
L293D . . . NE PACKAGE
(TOP VIEW)
D
Featuring Unitrode L293 and L293D
Products Now From Texas Instruments
D
D
D
D
D
D
D
D
D
Wide Supply-Voltage Range: 4.5 V to 36 V
Separate Input-Logic Supply
Internal ESD Protection
1,2EN
1A
V
CC1
4A
4Y
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
1Y
Thermal Shutdown
HEAT SINK AND
GROUND
HEAT SINK AND
High-Noise-Immunity Inputs
GROUND
2Y
2A
3Y
3A
Functionally Similar to SGS L293 and
SGS L293D
V
3,4EN
CC2
Output Current 1 A Per Channel
(600 mA for L293D)
L293 . . . DWP PACKAGE
(TOP VIEW)
Peak Output Current 2 A Per Channel
(1.2 A for L293D)
1
28
27
26
25
24
23
22
21
20
19
18
17
16
15
Output Clamp Diodes for Inductive
Transient Suppression (L293D)
1,2EN
1A
V
CC1
4A
2
3
1Y
NC
NC
NC
4Y
description/ordering information
4
NC
NC
NC
5
The L293 and L293D are quadruple high-current
half-H drivers. The L293 is designed to provide
bidirectional drive currents of up to 1 A at voltages
from 4.5 V to 36 V. The L293D is designed to
provide bidirectional drive currents of up to
600-mA at voltages from 4.5 V to 36 V. Both
devices are designed to drive inductive loads such
as relays, solenoids, dc and bipolar stepping
motors, as well as other high-current/high-voltage
loads in positive-supply applications.
6
7
HEAT SINK AND
GROUND
HEAT SINK AND
GROUND
8
9
10
11
12
13
14
NC
NC
2Y
2A
NC
NC
3Y
3A
V
3,4EN
CC2
All inputs are TTL compatible. Each output is a
complete totem-pole drive circuit, with
a
Darlington transistor sink and pseudo-
a
Darlington source. Drivers are enabled in pairs, with drivers 1 and 2 enabled by 1,2EN and drivers 3 and 4
enabled by 3,4EN. When an enable input is high, the associated drivers are enabled, and their outputs are active
and in phase with their inputs. When the enable input is low, those drivers are disabled, and their outputs are
off and in the high-impedance state. With the proper data inputs, each pair of drivers forms a full-H (or bridge)
reversible drive suitable for solenoid or motor applications.
ORDERING INFORMATION
ORDERABLE
PART NUMBER
TOP-SIDE
MARKING
†
PACKAGE
T
A
HSOP (DWP)
PDIP (N)
Tube of 20
Tube of 25
Tube of 25
Tube of 25
L293DWP
L293N
L293DWP
L293N
0°C to 70°C
L293NE
L293DNE
L293NE
L293DNE
PDIP (NE)
†
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
ꢊ
ꢊ
ꢉ
ꢒ
ꢥ
ꢅ
ꢠ
ꢇ
ꢓ
ꢞ
ꢔ
ꢟ
ꢏ
ꢙ
ꢒ
ꢗ
ꢕ
ꢘ
ꢅ
ꢈ
ꢔ
ꢈ
ꢖ
ꢗ
ꢡ
ꢘ
ꢙ
ꢟ
ꢚ
ꢛ
ꢜ
ꢜ
ꢝ
ꢝ
ꢖ
ꢖ
ꢙ
ꢙ
ꢗ
ꢗ
ꢖ
ꢞ
ꢞ
ꢢ
ꢟ
ꢠ
ꢚ
ꢚ
ꢡ
ꢡ
ꢗ
ꢝ
ꢜ
ꢛ
ꢞ
ꢞ
ꢙ
ꢘ
ꢢ
ꢔꢡ
ꢠ
ꢣ
ꢞ
ꢤ
ꢖ
ꢟ
ꢜ
ꢞ
ꢝ
ꢖ
ꢝ
ꢙ
ꢚ
ꢗ
ꢠ
ꢥ
ꢜ
ꢗ
ꢝ
ꢝ
ꢡ
ꢞ
ꢦ
Copyright 2004, Texas Instruments Incorporated
ꢚ
ꢙ
ꢟ
ꢝ
ꢙ
ꢚ
ꢛ
ꢝ
ꢙ
ꢞ
ꢢ
ꢖ
ꢘ
ꢖ
ꢟ
ꢡ
ꢚ
ꢝ
ꢧ
ꢝ
ꢡ
ꢚ
ꢙ
ꢘ
ꢨ
ꢜ
ꢏ
ꢗ
ꢛ
ꢡ
ꢞ
ꢝ
ꢜ
ꢗ
ꢥ
ꢜ
ꢚ
ꢥ
ꢩ
ꢜ
ꢝ ꢡ ꢞ ꢝꢖ ꢗꢫ ꢙꢘ ꢜ ꢤꢤ ꢢꢜ ꢚ ꢜ ꢛ ꢡ ꢝ ꢡ ꢚ ꢞ ꢦ
ꢚ
ꢚ
ꢜ
ꢗ
ꢝ
ꢪ
ꢦ
ꢊ
ꢚ
ꢙ
ꢥ
ꢠ
ꢟ
ꢝ
ꢖ
ꢙ
ꢗ
ꢢ
ꢚ
ꢙ
ꢟ
ꢡ
ꢞ
ꢞ
ꢖ
ꢗ
ꢫ
ꢥ
ꢙ
ꢡ
ꢞ
ꢗ
ꢙ
ꢝ
ꢗ
ꢡ
ꢟ
ꢡ
ꢞ
ꢞ
ꢜ
ꢚ
ꢖ
ꢤ
ꢪ
ꢖ
ꢗ
ꢟ
ꢤ
ꢠ
ꢥ
ꢡ
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265