Datasheet > JIP61089L

JIP61089L

更新时间： 2024-09-24 14:55:31

品牌	Logo	应用领域
捷捷微 - JJM		半导体
页数	文件大小	规格书
7页	313K
描述
半导体放电管

阅读下载

中文翻译

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

JIP61089L 数据手册

JIEJIE MICROELECTRONICS CO. , Ltd

JIP61089L Dual Programmable Thyristor Transient Voltage Suppressor Rev.3.2

DESCRIPTION:

JIP61089L is especially designed to protect monolithic SLIC

(subscriber line interfaces circuits) against transient overvoltages.

Positive overloads are clipped with 2 diodes. Negative

surges are suppressed by 2 thyristors, their breakdown

voltage being referenced to -V_BATthrough the gate. This

component presents a very low gate triggering current (I_GT)

in order to reduce the current consumption on printed

circuit board during the firing phase. A particular attention

Device package type SOP-8

has been given to the internal wire bonding. The “4-point”

configuration ensures reliable protection, eliminating the

overvoltage introduced by the parasitic inductances of the

wiring (Ldi/dt), especially for very fast transients.

Device package type SOP-8

FEATURES:

 Dual programmable transient suppressor.

 Wide negative firing voltage range: V_GKRM=-167V max .

 Low dynamic switching voltage: V_FRMand V_GK(BD).

 Low gate triggering current: I_GT=5mA max .

 Peak pulse current: I_PP=30A for 10/1000μs surge .

 Holding current: I_H=150mA min.

 Moisture sensitivity level: Level 3.

 UL 497B item recognized. (File No.: E480698).

 IEC61000-4-2 (ESD) ±30kV (air), ±30kV (contact).

APPLICATION:

JIP61089L is designed to protect communication equipment such as SPC exchanger from being

damaged by transient overvoltages at the second level.

TESTING STANDARDS

Wave Sharp

V_PP/I_PP

Type

Voltage

Current

10/700μs

5/310μs

2000V

40A

ITU-T K.20/21and K.45

Note 1 :The JIP61089L is intended to be used with a series combination of a 40 Ω or higher resistance and a

suitable overcurrent protector. Power fault compliance requires the series overcurrent element to open-circuit

or become high impedance. For equipment compliant to ITU-T recommendations K.20 or K.21 or K.45 only,

the series resistor value is set by the coordination requirements. For coordination with a 400V limit GDT, a

minimum series resistor value of 10Ω is recommended.

TEL：+86-513-83639777

-1 / 7-

http://www.jjwdz.com

12 3 4 5 6 7

中文翻译

下载PDF

与JIP61089L相关器件

型号	品牌	获取价格	描述	数据表
JIP61089Q	JJM	获取价格	半导体放电管
JIP61089S	JJM	获取价格	半导体放电管
JIP7015L1	JJM	获取价格	半导体放电管
JIP7038L1	JJM	获取价格	半导体放电管
JIP83121D	JJM	获取价格	半导体放电管
JISC7021A-1	LITEON	获取价格	Meet ROHS, Green Product Ultra bright A1InGaP Chip LED
JISC7021A-2	LITEON	获取价格	Meet ROHS, Green Product Extra thin 0.30H mm Chip LED Extra bright A1InGaP Chip LED
JISC7021A-4	LITEON	获取价格	Meet ROHS, Green Product Ultra bright A1InGaP Chip LED
JISC7021B-1	LITEON	获取价格	Meet ROHS, Green Product Ultra bright A1InGaP Chip LED
JISC7021B-10	LITEON	获取价格	Meet ROHS, Green Product Ultra bright A1InGaP Chip LED