IS-1825ASRH, ISL71823ASRH
®
Data Sheet
September 25, 2008
FN9065.3
Single Event and Total Dose Hardened,
High-Speed, Dual Output PWMs
Features
• Electrically Screened to DSCC SMD # 5962-02511
• QML Qualified per MIL-PRF-38535 Requirements
The single event and total dose hardened IS-1825ASRH and
ISL71823ASRH pulse width modulators are designed to be
used in high frequency, switching power supplies in either
voltage or current-mode configurations. Both designs
include a precision voltage reference, a low power start-up
circuit, a high frequency oscillator, a wide-band error
amplifier and a fast current-limit comparator.
• Radiation Environment
- Total Dose. . . . . . . . . . . . . . . . . . . . . 300krad(SI) (max)
- Latch-up Immune . . . . . . . . . . . . . Dielectrically Isolated
2
- SEU immune . . . . . . . . . . LET = 35MeV/mg/cm (max)
• Oscillator Frequency . . . . . . . . . . . . . . . . . . . .1MHz(max)
• High Output Drive Current . . . . . . . . . . . . . . .1A peak(typ)
• Low Start-up Current . . . . . . . . . . . . . . . . . . . 300µA(max)
The IS-1825ASRH features dual, alternating outputs
operating from zero to less than 50% duty-cycle, while the
ISL71823ASRH features dual, in-phase outputs operating
from zero to less than 100% duty cycle.
• Undervoltage Lockout
- Start Threshold . . . . . . . . . . . . . . . . . . . . . . . .8.8V(max)
- Stop Threshold . . . . . . . . . . . . . . . . . . . . . . . . 7.6V(min)
- Hysteresis. . . . . . . . . . . . . . . . . . . . . . . . . . 300mV(min)
Constructed with the Intersil Rad-hard Silicon Gate (RSG)
dielectrically isolated BiCMOS process, these devices are
immune to single event latch-up and have been specifically
designed to provide a high level of immunity to single event
transients. All specified parameters are guaranteed and
tested for 300krad(Si) total dose performance.
• Improved Soft-Start Function Compared with Commercial
1825A/1823A Types
• Pulse-by-Pulse Current Limiting
Detailed Electrical Specifications for these devices are
contained in SMD 5962-02511. A “hot-link” is provided
on our website for downloading the SMD.
• Latched Overcurrent Comparator with Full Cycle Restart
• Programmable Leading Edge Blanking
Applications
• Voltage or Current-Mode Switching Power Supplies
• Control of High Current MOSFET Drivers
• Motor Speed and Direction Control
Pinouts
IS1-1825ASRH, ISL71823ASRHQD
(CDIP2-T16 SBDIP)
IS9-1825ASRH, ISL71823ASRHQF
(CDFP4-F20 FLATPACK)
TOP VIEW
TOP VIEW
NC
INV
1
20
19
18
17
16
15
14
13
12
11
VREF
VCC
INV
NON-INV
E/A OUT
CLK/LEB
RT
1
2
3
4
5
6
7
8
16 VREF
15 VCC
2
NON-INV
E/A OUT
CLK/LEB
RT
3
OUT B
PGND
VC
14 OUT B
13 VC
4
5
12 PGND
11 OUT A
10 GND
6
VC
CT
CT
7
PGND
OUT A
GND
RAMP
SS
8
RAMP
SS
9
9
ILIM/SD
NC
10
ILIM/SD
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2002, 2005, 2008. All Rights Reserved
1
All other trademarks mentioned are the property of their respective owners.