DATASHEET
ISL70001ASEH
Radiation Hardened and SEE Hardened 6A Synchronous Buck Regulator
FN8365
Rev.3.03
Sep 16, 2022
The ISL70001ASEH is a radiation hardened and SEE
Features
hardened high-efficiency monolithic synchronous buck
• ±1% reference voltage over line, load, temperature and
radiation
regulator with integrated MOSFETs. This single chip power
solution operates over an input voltage range of 3V to 5.5V
and provides a tightly regulated output voltage that is
externally adjustable from 0.8V to ~85% of the input voltage.
• Current mode control for excellent dynamic response
• Full mil-temp range operation (T = -55°C to +125°C)
A
Output load current capacity is 6A for T < +145°C.
J
• 50% lower shutdown supply current than the ISL70001SEH
• Available in a thermally enhanced heatsink package - R48.B
• Highly efficient: 94% peak efficiency
The ISL70001ASEH uses peak current-mode control for
excellent output load transient response and features
integrated compensation and switches at a fixed frequency of
1MHz to reduce component size and count. In application
where two POLs are needed, two ISL70001ASEH devices can
be synchronized 180° out-of-phase to reduce the overall input
RMS ripple current. The internal synchronous power switches
are optimized for high efficiency and good thermal
performance.
• Operates from 3V to 5.5V supply
• Adjustable output voltage
- Two external resistors set V
from 0.8V to ~85% of V
IN
OUT
• Bidirectional SYNC pin allows two devices to be
synchronized 180° out-of-phase
The ISL70001ASEH incorporates fault protection for the
regulator. The protection circuits include input undervoltage,
output undervoltage, and output overcurrent.
• Power-good output voltage monitor
• Adjustable analog soft-start
• Input undervoltage, output undervoltage and output
overcurrent protection
High integration and class leading radiation tolerance makes
the ISL70001ASEH an ideal choice to power many of today’s
small form factor applications. Two devices can be
synchronized to provide a complete power solution for large
scale digital ICs, like field programmable gate arrays
(FPGAs), that require separate core and I/O voltages.
• Electrically screened to DLA SMD 5962-09225
• QML qualified per MIL-PRF-38535 requirements
• Radiation acceptance testing
- HDR [50-300rad(Si)/s] . . . . . . . . . . . . . . . . . . . 100krad(Si)
- LDR [<10mrad(Si)/s]. . . . . . . . . . . . . . . . . . . . . . .50krad(Si)
Applications
• SEE hardness (see SEE report for details)
2
• FPGA, CPLD, DSP, CPU Core or I/O voltages
- SEL and SEB LET . . . . . . . . . . . . 86.4MeV/mg/cm min
eff
• Low-voltage, high-density distributed power systems
2
- SEFI X-section (LET = 86.4MeV/mg/cm )
eff
-6
2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.4 x 10 cm max
2
- SET LET (< 1 pulse perturbation) 86.4MeV/mg/cm min
eff
100
95
5V Supply
ISL70001ASEH
CORE
AUX
I/O
90
SYNCH
85
RAD TOLERANT
FPGA
1.5V
1.8V
ISL75051SEH
3.3V
2.5V
80
75
70
1.2V
ISL70001ASEH
SYNCH
0
1
2
3
4
5
6
LOAD CURRENT (A)
FIGURE 1. TYPICAL APPLICATION
FIGURE 2. EFFICIENCY 5V INPUT, T = +25°C
A
FN8365 Rev.3.03
Sep 16, 2022
Page 1 of 27
© 2013-2022 Renesas Electronics