ISL6227
®
Data Sheet
December 21, 2006
FN9094.4
Dual Mobile-Friendly PWM Controller with
DDR Option
Features
• Provides regulated output voltage in the range 0.9V–5.5V
The ISL6227 dual PWM controller delivers high efficiency
precision voltage regulation from two synchronous buck DC/DC
converters. It was designed especially to provide power
regulation for DDR memory, chipsets, graphics and other
system electronics in Notebook PCs. The ISL6227’s wide
input voltage range capability allows for voltage conversion
directly from AC/DC adaptor or Li-Ion battery pack.
• Operates from an input battery voltage range of 5V to 24V
or from 3.3V/5V system rail
• Complete DDR1 and DDR2 memory power solution with
VTT tracking VDDQ/2 and a VDDQ/2 buffered reference
output
• Flexible PWM or HYS plus PWM mode selection with HYS
diode emulation at light loads for higher system efficiency
Automatic mode transition of constant-frequency synchronous
rectification at heavy load, and hysteretic (HYS) diode-
emulation at light load, assure high efficiency over a wide range
of conditions. The HYS mode of operation can be disabled
separately on each PWM converter if constant-frequency
continuous-conduction operation is desired for all load levels.
Efficiency is further enhanced by using the lower MOSFET
• r
DS(ON)
current sensing
• Excellent dynamic response with voltage feed-forward and
current mode control accommodating wide range LC filter
selections
• Undervoltage lock-out on VCC pin
• Power-good, overcurrent, overvoltage, undervoltage
protection for both channels
r
as the current sense element.
DS(ON)
Voltage-feed-forward ramp modulation, current mode control,
and internal feedback compensation provide fast response to
input voltage and load transients. Input current ripple is
• Synchronized 300kHz PWM operation in PWM mode
• Pb-free plus anneal available (RoHS compliant)
minimized by channel-to-channel PWM phase shift of 0°, 90° or
180° (determined by input voltage and status of the DDR pin).
Applications
• Notebook PCs and Desknotes
The ISL6227 can control two independent output voltages
adjustable from 0.9V to 5.5V, or by activating the DDR pin,
transform into a complete DDR memory power supply solution.
In DDR mode, CH2 output voltage VTT tracks CH1 output
voltage VDDQ. CH2 output can both source and sink current, an
essential power supply feature for DDR memory. The reference
voltage VREF required by DDR memory is generated as well.
• Tablet PCs/Slates
• Hand-held portable instruments
Ordering Information
PART
TEMP.
PKG.
PART #
MARKING RANGE (°C) PACKAGE DWG. #
ISL6227CA ISL6227CA -10 to +100 28 Ld QSOP M28.15
ISL6227CAZ ISL6227CAZ -10 to +100 28 Ld QSOP M28.15
In dual power supply applications the ISL6227 monitors the
output voltage of both CH1 and CH2. An independent PGOOD
(power good) signal is asserted for each channel after the
soft-start sequence has completed, and the output voltage is
within PGOOD window. In DDR mode CH1 generates the only
PGOOD signal.
(Note)
(Pb-free)
ISL6227IA
ISL6227IA
-40 to +100 28 Ld QSOP M28.15
ISL6227IAZ ISL6227IAZ
(Note)
-40 to +100 28 Ld QSOP M28.15
(Pb-free)
ISL6227HRZ ISL6227HRZ -10 to +100 28 Ld QFN
(Note) (Pb-free)
L28.5x5
Built-in overvoltage protection prevents the output from going
above 115% of the set point by holding the lower MOSFET on
and the upper MOSFET off. When the output voltage re-enters
regulation, PGOOD will go HIGH and normal operation
automatically resumes. Once the soft-start sequence has
completed, undervoltage protection latches the offending
channel off if the output drops below 75% of its set point value.
Adjustable overcurrent protection (OCP) monitors the voltage
ISL6227IRZ ISL6227IRZ -40 to +100 28 Ld QFN
L28.5x5
(Note)
(Pb-free)
Add -T to part number for Tape and Reel
NOTE: Intersil Pb-free plus anneal products employ special Pb-free
material sets; molding compounds/die attach materials and 100% matte
tin plate termination finish, which are RoHS compliant and compatible
with both SnPb and Pb-free soldering operations. Intersil Pb-free
products are MSL classified at Pb-free peak reflow temperatures that
meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
drop across the r
of the lower MOSFET. If more precise
DS(ON)
current-sensing is required, an external current sense resistor
may be used.
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2004-2006. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
5秒后页面跳转
SK海力士量产12层HBM3E，容量高达36GB
意法半导体传感器驱动Sphere，开启沉浸式电影新时代
摩尔斯微电子在美国约书亚树国家公园测试 Wi-Fi HaLow
贸泽上架Tallysman TW5386智能GNSS天线
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
