ISL6225
®
Data Sheet
December 28, 2004
FN9049.7
Dual Mobile-Friendly PWM Controller with
DDR Memory Option
The ISL6225 dual PWM controller delivers high efficiency and
tight regulation from two voltage regulating synchronous buck
DC/DC converters. The ISL6225 PWM power supply controller
was designed especially for DDR DRAM, SDRAM, and graphic
chipset applications in high performance desknote PCs,
notebook PCs, sub-notebook PCs, and PDAs.
Features
• Provides regulated output voltage in the range of 0.9V-5.5V
- High efficiency over wide load range
- Synchronous buck converter with hysteretic operation at
light load
- Inhibit Hysteretic mode on one, or both channels
• Complete DDR memory power solution
- VTT tracks VDDQ/2
- VDDQ/2 buffered reference output
• No current-sense resistor required
- Uses MOSFET rDS(ON)
- Optional current-sense resistor for precision overcurrent
Automatic mode selection of constant-frequency synchronous
rectification at heavy load, and hysteretic diode-emulation at
light load, assure high efficiency over a wide range of
conditions. The hysteretic mode of operation can be disabled
separately on each PWM converter if constant-frequency
continuous-conduction operation is desired for all load levels.
Efficiency is further enhanced by using the lower MOSFET
• Under-voltage lock-out on VCC pin
• Dual input voltage mode operation
- Operates directly from battery 5V to 24V input
- Operates from 3.3V or 5V system rail
- VCC from 5V only
• Excellent dynamic response
- Combined voltage feed-forward and average current
mode control
rDS(ON) as the current sense element.
Voltage-feed-forward ramp modulation, average current mode
control, and internal feedback compensation provide fast
response to input voltage and output load transients. Input
current ripple is minimized by channel to channel PWM
phase shift of 0°, 90°, or 180° determined by input voltage
and status of the DDR pin.
• Power-good signal for each channel
• 300kHz switching frequency
- 180° channel to channel phase operation for reduced input
ripple when not in DDR mode
- 0° channel to channel phase operation in DDR mode for
reduced channel interference
- 90° channel to channel phase operation for reduced input
ripple in DDR mode when VIN is at GND.
The ISL6225 can control two independent output voltages
adjustable from 0.9V to 5.5V or, by activating the DDR pin,
transform into a complete DDR memory power supply
solution. In DDR mode, CH2 output voltage VTT tracks CH1
output voltage VDDQ. CH2 output can both source and sink
current, an essential power supply feature for DDR memory
systems. The reference voltage VREF required by DDR
memory is generated as well.
• Pb-Free Available (RoHS Compliant)
In dual power supply applications the ISL6225 monitors the
output voltage of both CH1 and CH2. An independent
PGOOD (power good) signal is asserted for each channel
after the soft-start sequence has completed, and the output
voltage is within ±10% of the set point. In DDR mode CH1
generates the only PGOOD signal.
Applications
•
Mobile PCs
• PDAs
• Hand-held portable instruments
Ordering Information
Built-in overvoltage protection prevents the output from
going above 115% of the set point by holding the lower
MOSFET on and the upper MOSFET off. When the output
voltage decays below the overvoltage threshold, normal
operation automatically resumes. Once the soft-start
sequence has completed, under-voltage protection may
latch the ISL6225 off if either output drops below 75% of its
set point value.
PKG.
PART NUMBER
ISL6225CA
ISL6225CAZ (Note 1)
ISL6225CAZA (Note 1) -10 to 85 28 Ld SSOP (Pb-free) M28.15
NOTES:
1. IntersilPb-freeproductsemploy specialPb-freematerialsets; molding
compounds/die attach materials and 100% matte tin plate termination
finish, which are RoHS compliant and compatible with both SnPb and
Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed
the Pb-free requirements of IPC/JEDEC J STD-020.
2. Add “-T” for Tape and Reel.
TEMP. (°C)
-10 to 85
PACKAGE
28 Ld SSOP
DWG. #
M28.15
-10 to 85 28 Ld SSOP (Pb-free) M28.15
Adjustable overcurrent protection (OCP) monitors the
voltage drop across the rDS(ON) of the lower MOSFET. If
more precise current-sensing is required, an external current
sense resistor may be used.
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2002-2004. All Rights Reserved
1
All other trademarks mentioned are the property of their respective owners.
5秒后页面跳转
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
AMD宣布全球裁员约1000人，调整战略聚焦增长
英伟达新AI芯片Rubin或提前半年亮相
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
