IS25C08B
8K-BIT SPI SERIAL
ELECTRICALLY ERASABLE PROM
Preliminary Information
September 2009
DESCRIPTION
FEATURES
The IS25C08B is an 8Kbit (1024x 8) electrically
erasable PROM devices that use the Serial Peripheral
Interface (SPI) for communications.
•ꢀ SerialꢀPeripheralꢀInterfaceꢀ(SPI)ꢀCompatible
—ꢀSupportsꢀSPIꢀꢀModesꢀ0ꢀ(0,0)ꢀandꢀ3ꢀ(1,1)
•ꢀ Wide-voltageꢀOperation
—ꢀVccꢀ=ꢀ1.8Vꢀtoꢀ5.5V
•ꢀ LowꢀpowerꢀCMOS
This EEPROM operates in a wide voltage range of 1.8V
to 5.5V to be compatible with most application voltages.
ISSI designed this device to be a practical, low-power SPI
EEPROM solution. The devices are offered in lead-free,
RoHS,halogenfreeorGreen.Theavailablepackagetypes
are 8-pin SOIC, TSSOP, UDFN and CSP.
ꢀꢀ —ꢀOperatingꢀcurrentꢀlessꢀthanꢀ1ꢀmAꢀ(1.8V)
ꢀꢀ —ꢀStandbyꢀcurrentꢀlessꢀthanꢀ1ꢀµAꢀ(1.8V)
•ꢀ BlockꢀWriteꢀProtection
—ꢀProtectꢀ1/4,ꢀ1/2,ꢀorꢀEntireꢀArray
•ꢀ 32-byteꢀpageꢀwriteꢀmodeꢀ
ꢀ
—ꢀPartialꢀpageꢀwritesꢀallowed
•ꢀ 20ꢀMHzꢀClockꢀRateꢀ(5V)
•ꢀ Selfꢀtimedꢀwriteꢀcyclesꢀ(5ꢀmsꢀTypical)
•ꢀ High-reliability
—ꢀEndurance:ꢀ1ꢀmillionꢀcyclesꢀperꢀbyte
—ꢀDataꢀretention:ꢀ100ꢀyears
•ꢀ Industrialꢀgrade
The functional features of the IS25C08B allow them to
be among the most advanced serial non-volatile memo-
ries available. Each device has a Chip-Select (CS) pin,
and a 3-wire interface of Serial Data In (SI), Serial Data
Out (SO), and Serial Clock (SCK). While the 3-wire
interface of the IS25C08B provides for high-speed ac-
cess, a HOLD pin allows the memories to ignore the
interface in a suspended state; later the HOLD pin re-
activates communication without re-initializing the serial
sequence. A Status Register facilitates a flexible write
•ꢀ Packages:ꢀSOIC/SOP,ꢀTSSOP,ꢀUDFNꢀandꢀCSP
protection mechanism, and a device-ready bit (RDY).
Copyright © 2008 Integrated Silicon Solution, Inc. All rights reserved. ISSI reserves the right to make changes to this specification and its products at any time without
notice. ISSI products are not designed, intended, authorized or warranted for use as components in systems or equipment intended for critical medical or surgical equip-
ment, aerospace systems, or for other applications planned to support or sustain life. It is the customer's obligation to optimize the design in their own products for the best
performance and optimization on the functionality and etc. ISSI assumes no liability arising out of the application or use of any information, products or services described
herein. Customers are advised to obtain the latest version of this device specification before relying on any published information and prior placing orders for products.
Integrated Silicon Solution, Inc.
Preliminary Information Rev. 00A
08/25/09
1