Data Sheet No. PD60166 revS
IR2136/IR21362/IR21363/IR21365/
(
&
IR21366/IR21367/IR21368 J S) & (PbF)
3-PHASE BRIDGE DRIVER
Features
Floating channel designed for bootstrap operation
Fully operational to +600V
•
Packages
Tolerant to negative transient voltage - dV/dt immune
Gate drive supply range from 10 to 20V (IR2136/IR21368),
11.5 to 20V (IR21362) or 12 to 20V (IR21363/IR21365/
IR21366/IR21367)
•
Undervoltage lockout for all channels
•
•
•
•
•
•
28-Lead SOIC
Over-current shutdown turns off all six drivers
Independent 3 half-bridge drivers
Matched propagation delay for all channels
Cross-conduction prevention logic
Lowside outputs out of phase with inputs. High side
outputs out of phase (IR2136/IR21363/IR21365/
28-Lead PDIP
44-Lead PLCC w/o 12 leads
Feature Comparison: IR2136/IR21362/IR21363/
IR21365/IR21366/IR21367/IR21368
IR21366/IR21367/IR21368) or in phase
(IR21362) with inputs.
3.3V logic compatible
•
•
Part
Input Logic
IR21365
HIN, LIN
400ns
380ns
2.7V
IR21368
HIN,LIN
400ns
380ns
2.0V
IR2136 IR21362 IR21363
HIN, LIN HIN/LIN HIN, LIN
IR21366 IR21367
HIN, LIN HIN, LIN
Lower di/dt gate driver for
better noise immunity
Externally programmable
delay for automatic fault
clear
Ton (typ.)
Toff (typ.)
VIH (typ.)
VIL (typ.)
400ns
380ns
2.7V
1.7V
0.46V
8.9V
400ns
380ns
2.7V
400ns
380ns
2.7V
250ns
180ns
2.0V
250ns
180ns
2.0V
•
1.7V
1.3V
1.7V
1.7V
1.3V
1.3V
Also available LEAD-FREE
Vitrip+
4.3V
11.2V
11.0V
4.3V
8.9V
8.2V
•
0.46V
10.4V
9.4V
0.46V
11.2V
11.0V
0.46V
11.2V
11.0V
4.3V
11.2V
11.0V
UV CC/BS+
UV CC/BS-
8.2V
Description
TheIR2136/IR21362/IR21363/IR21365/IR21366/IR21367/IR21368(J&S)arehighvotage, highspeed power MOSFET
and IGBT drivers with three independent high and low side referenced output channels for 3-phase applications.
Proprietary HVIC technology enables ruggedized monolithic construction. Logic inputs are compatible with CMOS
or LSTTL outputs, down to 3.3V logic. A current trip function which terminates all six outputs can be derived from
an external current sense resistor. An enable function is available to terminate all six outputs simultaneously. An
open-drain FAULT signal is provided to indicate that an overcurrent or undervoltage shutdown has occurred.
Overcurrent fault conditions are cleared automatically after a delay programmed externally via an RC network
connected to the RCIN input. The output drivers feature a high pulse current buffer stage designed for minimum
driver cross-conduction. Propagation delays are matched to simplify use in high frequency applications. The
floating channel can be used to drive N-channel power MOSFETs or IGBTs in the high side configuration which
operates up to 600 volts.
up to 600V
Typical Connection
VCC
VCC
HIN1,2,3 / HIN1,2,3
HIN1,2,3
LIN1,2,3
FAULT
EN
/
HIN1,2,3
VB1,2,3
HO1,2,3
VS1,2,3
LIN1,2,3
FAULT
EN
(Refer to Lead Assign-
ments for correct pin con-
figuration). This/These
diagram(s) show electri-
cal connections only.
Please refer to our Appli-
TO
LOAD
RCIN
ITRIP
VSS
LO1,2,3
COM
cation
Notes
and
DesignTips for proper cir-
cuit board layout.
IR2136(2)(3)(5)(6)(7)(8)
GND
www.irf.com
1