REVISION B
IPL1-1XX-02-XXX-DH-K-TR
No OF POSITIONS
-02 THRU -25 (PER ROW)
TAPE AND REEL
(SEE NOTES 9 & 12)
FIG. 1
(IPL1-110-02-XXX-DH-K-TR SHOWN)
LEAD STYLE
-02: DOUBLE HORIZONTAL
(USE T-1S64-XX-XXX)
C
POLARIZATION
-K: KEYED POLARIZATION
(No. OF POS. x .100[2.54]) + .075[1.91]
ROW SPECIFICATION
-DH: DOUBLE HORIZONTAL
2
MAX SWAY
(TYP)
PLATING SPECIFICATION
-F: FLASH SELECTIVE (USE T-1S64-XX-F)
-L: LIGHT SELECTIVE (USE T-1S64-XX-L)
-S: SELECTIVE (USE T-1S64-XX-S)
C
.025 0.64 SQ. REF
(No. OF POS. - 1) x .100[2.54]
-STL: SELECTIVE TIN/LEAD(USE T-1S64-XX-STL)
.130 3.30
01
02
.270 6.86 REF
.250 6.35 REF
.040 1.02 REF
.100 2.54
.100 2.54 (TYP)
SEE NOTE 4
.100 2.54 REF
2 MAX TOE
(TYP)
(No. OF POS. x .100[2.54]) + .160[4.06] REF
"A"
SEE NOTE 7
.220 5.59
IPL1-XX-DH-X
SEE NOTE 8
.300 7.62 REF
SEE NOTE 10
WT-28-01-T
T-1S64-09-XXX
.023 0.57 REF (TYP)
.076 1.93 REF (TYP)
T-1S64-16-XXX
"A"
.100 2.54
(TYP)
2
MAX SWAY (TYP)
C
.010[0.25]
SECTION "A"-"A"
.025 0.64 SQ. REF
(TYP)
(No. OF POS. - 1) x .100[2.54]
C
NOTES:
C
1.
REPRESENTS A CRITICAL DIMENSION.
PROPRIETARY NOTE
UNLESS OTHERWISE SPECIFIED,
2. MINIMUM TERMINAL /WELD TAB RETENTION: 1.0LB.[4.4N}
3. PARTS TO BE MOLDED TO POSITION.
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
4. POST MUST BE WITHIN .005[0.13] OF EACH OTHER.
DECIMALS
ANGLES
5. ALL PIN TO PIN DIMENSIONS TO BE MEASURED FROM TIP TO TIP.
6. DIMENSION TO BE MEASURED AT BEND.
.XX: .01 [0.3]
2
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322
.XXX: .005 [0.13]
7. TIP TO BE FLUSH TO .010[0.254] BELOW TOP OF SHROUD.
8. THIS NUMBER REPRESENTS THE NUMBER OF POSITIONS PER ROW
ONLY AND IS NOT INTENDED TO BE USED IN POSITION NUMBERING.
9. PARTS TO BE PACKAGED IN TAPE AND REEL.
.XXXX: .0020 [0.051]
SHEET SCALE: 2:1
MATERIAL:
DO NOT SCALE DRAWING
DESCRIPTION:
.100[2.54] DOUBLE ROW TERMINAL ASSEMBLY
DWG. NO.
INSULATOR: L.C.P. COLOR: BLACK
TERMINAL: PHOS BRONZE
10. INDENTION FROM WELD TAB CARRIER IS ALLOWABLE.
11. WELD TABS TO BE INSERTED WHILE ON CARRIER.
12. FOR QUANTITIES TO 49 PIECES, NO LEADER, TRAILER, OR REEL WILL BE SUPPLIED.
FOR QUANTITIES 50-124 PIECES, NO LEADER OR TRAILER WILL BE SUPPLIED.
IPL1-1XX-02-XXX-DH-K-TR
BY:
T NEWTON 02/29/2008 SHEET 1 OF 2
F:\DWG\MISC\MKTG\IPL1-1XX-02-XXX-DH-K-TR-MKT.SLDDRW