XDMX-XX-X-XX.XX-XXX-XXX
TAIL SPECIFICATION
(SEE SECT "A"-"A" & "B"-"B")
I: D = .125[3.18] (T-1S7-01-X)
**E: D = .200[5.08] (T-1S7-02-X)
C
REVISION AP
"A"
"C" .125 3.18
OPTION SPECIFICATION
SEE OPTIONS
(SEE SHT 2 & SHT 3)
"A"
DO NOT
SCALE FROM
THIS PRINT
OPTION SPECIFICATION
ROW SPECIFICATION
-S: SINGLE
-D: DOUBLE
SEE OPTIONS
(SEE SHT 2 & SHT 3)
LENGTH OF CABLE
MEASURED IN INCHES
(SEE FIG 1, "C" DIM)
NO OF CONDUCTORS (SEE NOTE 3)
(-02 THRU -32 PER ROW)
USE CABLE CB-XX-28-7/36-100-C (XDMS)
"B"
USE CABLE CB-XX-28-7/36-050-C (XDMD)
.015 [.38]
.005 [.13]
CONNECTOR SPECIFICATION
"A"
= "XX" X .100[2.54] + .019[0.48] (-01 THRU -31)
OR 3.210[81.53] REF (-32)
-S: (SINGLE) ONE XDM ASSEMBLY
-D: (DOUBLE) TWO XDM ASSEMBLIES
-ONE ON EACH END
.015 [.38]
"B"
= "XX" X .100[2.54] + .059[1.50] (-01 THRU -31)
OR.300.52[.153]0[82.55] REF (-32)
* NOTE: STANDARD COLOR-CODED CABLE N/A
FOR DOUBLE ROW 31 & 32 POSITION -
SEE -G OPTION.
-T: (TRANSFER-IDMS) ONE XDMS & ONE IDS
-ONE ON EACH END
-T: (TRANSFER-IDMD) ONE XDMD & ONE IDD
- ONE ON EACH END
** = EXISTING CUSTOMERS ONLY
BROWN OR RED WIRE
INDICATES PIN #1 (SEE NOTE 3)
RIBS OF GRAY CABLE GO
TO CAPS SIDE EXCEPT ON
REVERSE ASSEMBLIES.
C
"E"
FIRST PRESS END
SEE NOTE 4
C
(XDMX ASSEMBLY)
-T CONNECTOR SPECIFICATION
.235±.005 5.97±0.13
(SEE NOTE 16)
FIG 3
XDMD-13-D-XX.XX-X-X-T SHOWN
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1)
FIG 1
PIN #1
XDMD-13-D-XX.XX-X-X SHOWN
"B"
+.003
-.002
+0.08
2.29
-0.05
.090
C
C
L
L
IMC-32-S
IMB-32-S
IMC-32-D
"B"
+.003
+0.08
2.29
-0.05
.090
-.002
IMB-32-D
SEE NOTE 6
T-1S7-XX-X
"A"
SEE NOTE 6
T-1S7-XX-X
3° MAX TOE
"D" REF
"D" REF
C
C
+.010
-.025
+0.25
.125
3.18
-0.64
SECTION "A"-"A"
(XDMD ASSEMBLY)
SECTION "B"-"B"
(XDMS ASSEMBLY)
NOTES:
(REFER TO XMD-XX-X ASSEMBLY)
(REFER TO XMS-XX-X ASSEMBLY)
BROWN OR RED WIRE
C
1.
REPRESENTS A CRITICAL DIMENSION.
INDICATES PIN #1
(SEE NOTE 3)
2. OPTION -SXX WHEN MATING DOUBLE ROW CONNECTOR WITH 2 SINGLE ROW CONNECTORS, THE OUTER
MOST SINGLE WILL BE CONNECTED TO CONDUCTOR #1 AND THE INSIDE SINGLE TO CONDUCTOR #2.
3. ON FIRST CABLE INSERTION PRESS, THE BROWN WIRE (COLORED CABLE) OR THE RED WIRE (GRAY CABLE )
IS POSITIONED TO THE RIGHT WITH THE "FAT END" OF THE BASE AND CAP.
FIG 2
XDMS-13-D-XX.XX-X-X SHOWN
(DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1)
4. WHEN CUTTING BASE AND CAPS TO POSITION, END WALLS ON CUT ENDS SHALL BE .010 [.25] MIN.
5. CABLE CAN BE RECESSED OR EXTENDED .010 [.25] MAX. FROM FLUSH
6. STANDOFFS ON BASE SHALL STAND .010 [.25] MIN. FROM SURFACE OF IMB-32-X.
7. OPTION -PXX:POLARIZING OPTION CAN ONLY BE USED ON IDX END OF -T (TRANSFER) OPTION.
8. WHEN DAISY CHAINING A TRANSFER END OPTION, ONLY THE FIRST CONNECTOR IS MALE; THE REMAINING
CONNECTORS ARE FEMALE.
9. A CHAMFER ON THE END OF THE CAP IS GUARANTEED ON FINAL ASSEMBLIES
THAT ARE AT LEAST 18 POSITIONS FOR MALE AND FEMALE TERMINATION.
10. ALL ASSEMBLIES TO BE 100% ELECTRICALLY TESTED FOR SHORTS AND OPENS.
11. ALL ASSEMBLIES TO BE 100% HI-POT TESTED AT 1000V.
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS CONFIDENTIAL AND
PROPRIETARY INFORMATION AND ALL DESIGN,
MANUFACTURING, REPRODUCTION, USE, PATENT RIGHTS
AND SALES RIGHTS ARE EXPRESSLY RESERVED BY SAMTEC,
INC. THIS DOCUMENT SHALL NOT BE DISCLOSED, IN WHOLE
OR PART, TO ANY UNAUTHORIZED PERSON OR ENTITY NOR
REPRODUCED, TRANSFERRED OR INCORPORATED IN ANY
OTHER PROJECT IN ANY MANNER WITHOUT THE EXPRESS
WRITTEN CONSENT OF SAMTEC, INC.
*
*
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS
ANGLES
2
.XX: .01 [0.3]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322
.XXX: .005 [0.13]
.XXXX: .0020 [0.051]
12. CONTACT NOT TO BE VISIBLE THROUGH THE END WALL OF IMC-32-X CAP.
13. REFERENCE XMD-XX-X (AND IDX-XX-X-PXX FOR -T OPTION) FOR CUT DIMENSIONS.
14. WHEN CUTTING CABLE TO LENGTH, CONDUCTORS SHOULD NOT EXTEND PAST THE CABLE INSULATION,
EXTENDING LESS THAN 25% OF CABLE THICKNESS ON CONSECUTIVE AND LESS THAN 50%
OF CABLE THICKNESS ON NON-CONSECUTIVE STRANDS IS CONSIDERED A PROCESS INDICATOR.
15. PACKAGE WITH PAPER COVERS EITHER CRD-IDC004 OR CRD-IDC005 BASED ON POSITION.
16. DEMINSION FROM TOP OF CAP TO STANDOFF.
SHEET SCALE: 2:1
MATERIAL:
DO NOT SCALE DRAWING
DESCRIPTION:
INSULATOR: VALOX DR-48, COLOR: BLACK
CONTACT: BeCu
ASSEMBLY INSULATION DISPLACEMENT TERMINAL CONNECTOR
DWG. NO.
TERMINAL: PHOSPHOR BRONZE
CABLE: TINNED COPPER/PVC
XDMX-XX-X-XX.XX-XXX-XXX
17. SAME AS -SXX EXCEPT OUTER STRIP CONNECTED TO CONDUCTOR #2 AND INSIDE STRIP CONNECTED TO
CONDUCTOR #1.
BY:
JORDAN 12/30/1987 SHEET 1 OF 3
F:\DWG\MISC\Mktg\XDMX-XX-X-XX.XX-XXX-XXX-MKT.SLDDRW
5秒后页面跳转
NTC热敏电阻与PTC热敏电阻的应用原理及应用范围
GTO与普通晶闸管相比为什么可以自关断？为什么普通晶闸管不能呢？从GTO原理、应用范围带你了解原因及推荐型号
LF353数据手册解读：特性、应用、封装、引脚说明、电气参数及替换型号推荐
A4950资料手册解读：特性、应用、封装、引脚功能、电气参数及代换型号
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
