HX1081
•
•
•
•
SAW Frequency Stabilized
Fundamental-mode Oscillation at 1090.0 MHz
Designed for ATC/TCAS Transponder Applications
Complies with Directive 2002/95/EC (RoHS)
1090.0 MHz
SAW
P
b
The frequency of this oscillator is stabilized by UHF surface-acoustic-wave (SAW) tech-
nology, providing excellent performance in a compact, rugged oscillator operating at the
fundamental frequency of 1090.0 MHz. The highly-reliable HX1081 is designed for use
in Mode-S Air Traffic Control Transponders/Traffic Alert and Collision Avoidance Sys-
tems (TCAS).
Oscillator
Absolute Maximum Ratings
Rating
Value
Units
DC Supply Voltage
3.0 to +3.7
-55 to +105
-55 to +125
VDC
Powered
Storage
Ambient Temperature
°C
Electrical Characteristics
Characteristic
Sym
Notes
Minimum
Typical
Maximum
1090.25
±250
+13
Units
MHz
kHz
dBm
ns
f
Operating Frequency
Absolute Frequency
1089.75
1090.00
O
1, 7
∆f
Tolerance from 1090.0 MHz
O
P
RF Output Power
Start-up Time
3, 6
2, 8
+10
+12
O
500
Discrete Spurious
Second Harmonics
Third and Higher Harmonics
Nonharmonic
-25
-35
-20
2, 3, 4
dBc
-30
< -100
-80
SSB Phase Noise
RF Impedance
1 kHz Offset
-90
2, 3, 4
dBc/Hz
10 kHz Offset
-110
Z
Nominal Impedance
Operating Load VSWR
Operating/Enable Voltage
Operating Current
3
50
Ω
O
G
3, 5
1.5:1
3.7
L
V
3.3
37
DC Power Supply
3.0
-55
VDC
mA
°C
CC
3, 6
3, 6
I
40
CC
T
Operating Ambient Temperature
+105
A
Lid Symbolization (YY=Year, WW=Week)
RFM HX1081 YYWW
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. COCOM CAUTION: Approval by the U.S.
Department of Commerce is required prior to export of this device.
Notes:
1. One or more of the following United States patents apply: 4,760,352; 5,787,117; and 7,260,375.
2. Unless noted otherwise, all specifications are listed at T = +25 ±2 °C, V = nominal voltage ±0.01 VDC, and load impedance = 50 Ω with
A
CC
VSWR ≤ 1.5:1.
3. The design, manufacturing process, and specifications of this device are subject to change without notice.
4. Applies to oscillator only and not to sidebands caused by external electrical or mechanical sources. (Dedicated external voltage regulation with
low-frequency filtering for the DC power supply and proper circuit board layout are recommended for optimum spectral purity.)
5. For specified maximum operating load VSWR,any angle, at F . No instability or damage will occur for any passive load impedance.
O
6. For any combination of V and T within the specified operating ranges.
CC
A
7. Applies for any combination of Note 5 and 6 conditions.
8. Start-up time is defined as the time from when 90% of Vcc is applied to the Enable Pin until the RF output reaches 90% of its steady-state
output level.
www.RFM.com E-mail: info@rfm.com
© 2011 by RF Monolithics, Inc.
Page 1 of 3
HX1081 6/20/11