Applicable Standard
-40 C TO +105 C
AC 200 V , DC 250 V
3 A
-10 C TO +60 C
Rating
Operating temperature range
Storage Temperature Range
Applicable Cable
Voltage
Current
Specifications
TEST METHOD
ITEM
REQUIREMENTS
QT AT
Construction
General examination
Marking
Visually and by measuring instrument.
Confirmed visually.
According to drawing.
×
×
×
×
Electrical Characteristics
20 m max.
Contact resistance
Contact measured at DC 1 A (MIL-C-2316)
×
×
×
×
1000 M min.
Insulation resistance
DC 500 V DC. (MIL-STD-1344 3003)
Voltage proof
AC 900 V AC for 1 min. (MIL-STD-1344 3001)
No flashover or breakdown.
Mating and Unmating Forces
×
×
Mechanical Characteristics
Connector Mating and
Measured with an applicable connector.
: 50 N max.
×
×
×
―
―
―
Unmating Forces
Contact Resistance
:
30 m max.
Mechanical operation
Mated and unmated 30 times.
(MIL-C-5015 4.6.12.2)
① No electrical discontinuity of 10 s.
② No damage, cracks or looseness of parts.
Vibration
Shock
Frequency 10 to 500 Hz, single amplitude 0.75 mm,
98 m/s2 at 3 h, for 3 directions.
(MIL-STD-1344 2005,conditionⅡ)
Acceleration: 490m/s², half sine wave pulses of 11ms.
Performed 3 times in each of three mutually
perpendicular directions.
①
②
No electrical discontinuity of 10 s.
×
―
No damage, cracks or looseness of parts.
(MIL-STD-1344 2004, condition E)
Environmental Characteristics
Rapid change of temperature Temperature -55 → R/T(1) → +105→ R/T ゚C
① Insulation Resistance: 500 MΩ min.
② No damage, cracks or looseness of parts.
×
×
―
―
Time 30 → 2〜3 → 30 → 2〜3 min for 5 cycles.
Damp heat
Subjected to 71゚C, at a humidity of 95% for 336h.
①
②
③
Insulation Resistance: 50 MΩ min
(At high humidity).
(steady state)
(MIL-C-5015 4.6.10)
Insulation Resistance: 500MΩ min (When
dry).
No damage, cracks or looseness of parts.
Corrosion sulphur dioxide
Exposed in S02:670ppm 40℃ for 8 h.
Exposed in air atmosphere 18 to 28℃ for 16 h.
(DIN 50018)
No heavy corrosion which impairs functionality.
×
―
Sealing
Subjected to a depth of 1 m for 0.5 h. (JIS B 6015) No water penetration inside connector.
×
×
―
―
Airtightness
40 kPa of air pressure applied to the inside of the
mated connector for 30s.
No air bubbles emitted from the inside of the
connector.
Resistance to soldering
heat
Place soldering iron (iron tip temperature +380±
10℃ )and solder to soldering pot area for 3 to 4 s.
No deformation of case and excessive looseness
Of the terminals.
×
―
Solderability
Place soldering iron (iron tip temperature +350±
10℃ )and solder to soldering pot area for 2 to 3 s.
A soldering side is to be wet with solder.
And, no small lump of the solder.
×
×
―
―
Corrosion salt mist
Subjected to 5% salt spray for 720h.
(MIL-STD-1344 3001, condition B)
No heavy corrosion which impairs functionality.
COUNT
DESCRIPTION OF REVISIONS
DESIGNED
TR.YAMANOUE
CHECKED
DATE
△
2
1
DIS-C-00017588
HY.KOBAYASHI
YH.YAMADA
20240510
20200609
20200609
20200608
Remarks
NOTES(1) R/T :Room Temperature
APPROVED
CHECKED
DESIGNED
HY.KOBAYASHI
KN.IKEHARA
(2) Sealing and airtightness shall be tested under mated condition
with an applicable connector.
2
(3)(Deleted remark)
DRAWN
KN.IKEHARA
20200608
Unless otherwise specified, refer to IEC 60512 (JIS C 5402).
Note QT:Qualification Test AT:Assurance Test X:Applicable Test
DRAWING NO.
PART NO.
CODE NO.
ELC-392042-00-00
HR34P-10WR-10P
SPECIFICATION SHEET
HIROSE ELECTRIC CO., LTD.
2
△
1/1
CL0134-0079-0-00
FORM HD0011-2-1