APPLICABLE STANDARD
-20 C TO
+85 C
-10
C TO
+60 C
RATING
OPERATING TEMPERATURE RANGE
STORAGE TEMPERATURE RANGE
APPLICABLE CABLE
VOLTAGE
CURRENT
AC 200 V , DC 250 V
3 A
(φ6.5 TO φ7.3)
SPECIFICATIONS
TEST METHOD
ITEM
REQUIREMENTS
QT AT
CONSTRUCTION
GENERAL EXAMINATION
MARKING
VISUALLY AND BY MEASURING INSTRUMENT.
CONFIRMED VISUALLY.
ACCORDING TO DRAWING.
×
×
×
×
ELECTRIC CHARACTERISTICS
―
×
20 m MAX.
CONTACT RESISTANCE
CONTACT SHALL BE MEASURED AT DC 1 A (MIL-C-2316)
×
×
1000
M MIN.
INSULATION RESISTANCE
DC 500 V DC. (MIL-STD-1344 3003)
VOLTAGE PROOF
AC 900 V AC FOR 1 min. (MIL-STD-1344 3001)
NO FLASHOVER OR BREAKDOWN.
×
×
×
×
―
―
MECHANICAL CHARACTERISTICS
CONTACT INSERTION AND
0
φ0.736
BY STEEL GAUGE.
INSERTION AND WITHDRAWAL FORCES : 0.2 N MIN.
-0.003
WITHDRAWAL FORCES
CONNECTOR INSERTION AND
WITHDRAWAL FORCES
MEASURED BY APPLICABLE CONNECTOR.
INSERTION FORCE : 70 N MAX.
WITHDRAWAL FORCE : 50 N MAX.
LOCKING DEVICE WITH UNLOCK
CONTACT RESISTANCE :
30
m MAX.
MECHANICAL OPERATION
VIBRATION
500 TIMES INSERTIONS AND EXTRACTIONS.
×
×
―
―
(MIL-C-5015 4.6.12.2)
① NO ELECTRICAL DISCONTINUITY OF 10 s.
② NO DAMAGE, CRACK AND LOOSENESS OF PARTS.
FREQUENCY 10 TO 500 Hz, SINGLE AMPLITUDE 0.75 mm,
98 m/s2 AT 3 h, FOR 3 DIRECTIONS.
(MIL-STD-1344 2005,CONDITIONⅡ)
m/s2
DIRECTIONS OF PULSE 11ms AT 3 TIMES
×
×
―
―
① NO ELECTRICAL DISCONTINUITY OF 10 s.
SHOCK
490
FOR 3 DIRECTIONS. (MIL-STD-1344 2004,CONDITION E) ② NO DAMAGE, CRACK AND LOOSENESS OF PARTS.
CONTACT RETENTION FORCE
APPLYING A PULL FORCE THE WIRE THE APPLICABLE CRIMPED
CONTACT IS ASSEMBLED THE BODY.
20 N MIN.
ENVIRONMENTAL CHARACTERISTICS
RAPID CHANGE OF TEMPERATURE TEMPERATURE -55→ R/T(1) → +85 → R/T ℃
① INSULATION RESISTANCE: 500 MΩ MIN.
×
×
―
―
TIME 30 → 2 TO 3 → 30 → 2 TO 3 min UNDER 5 CYCLES. ② NO DAMAGE, CRACK AND LOOSENESS OF PARTS.
DAMP HEAT
EXPOSED AT 71 ℃, 95 %, 336 h. (MIL-C-5015 4.6.10)
① INSULATION RESISTANCE: 50 MΩ MIN
(AT HIGH HUMIDITY).
(STEADY STATE)
② INSULATION RESISTANCE: 500MΩ MIN (AT DRY).
③ NO DAMAGE, CRACK AND LOOSENESS OF PARTS.
SEALING(2)
EXPOSED AT A DEPTH OF 1 m FOR 0.5 h.
(JIS B 6015) NO WATER PENETRATION INSIDE CONNECTOR.
×
×
―
―
AIRTIGHTNESS(2)
APPLY AIR PRESSURE 40 kPa FOR 30 SEC TO INSIDE
CONNECTOR.
NO AIR BUBBLES FROM CONNECTOR INTERFACE.
OIL RESISTING(2)
DROP CUTTING OIL FOR 48 HOURS AT THE RATE OF 0.5L
NO OIL SEEPAGE INSIDE CONNECTOR.
×
×
―
―
EVERY HOUR.
EXPOSED IN 5% SALT WATER SPRAY FOR 48h.
(MIL-STD-1344 3001,CONDITION B)
(JIS B 6015)
NO HEAVY CORROSION RUINS THE FUNCTION.
CORROSION SALT MIST
DRY HEAT
COLD
EXPOSED AT + 85 ℃,96 h.
NO DAMAGE,CRACK AND LOOSENESS OF PARTS.
NO DAMAGE,CRACK AND LOOSENESS OF PARTS.
X
X
―
―
EXPOSED AT - 55 ℃,96 h.
COUNT
DESCRIPTION OF REVISIONS
DESIGNED
CHECKED
DATE
△
0
REMARK
APPROVED
CHECKED
DESIGNED
HY.KOBAYASHI
HY.KOBAYASHI
DS.MATSUNE
18.02.26
18.02.26
18.02.24
NOTES(1) R/T :ROOM TEMPERATURE.
(2) SEALING, AIRTIGHTNESS AND OIL RESISTING SHALL BE TESTED UNDER MATED
CONDITION WITH AN APPLICABLE CONNECTOR.
(3) THE STD. VALUE ABOVE INDICATES AT THE STATE APPLICABLE CONTACT
ASSEMBLED.
DRAWN
AI.NISHIYAMA
18.02.16
Unless otherwise specified, refer to IEC 60512(JIS C5402).
Note QT:Qualification Test AT:Assurance Test X:Applicable Test
DRAWING NO.
ELC-117753-31-00
PART NO.
CODE NO.
HR08D-12WPN-10SC(31)
SPECIFICATION SHEET
HIROSE ELECTRIC CO., LTD.
0
CL108-0269-5-31
△
1/1
FORM HD0011-2-1