APPLICABLE STANDARD
MIL-C-5015
-40 C TO
+125 C
-10
C TO
+60 C
OPERATING
STORAGE TEMPERATURE
RANGE
RATING
TEMPERATURE RANGE
VOLTAGE
AC 500 V , DC 700 V
13 A(1)
CURRENT
APPLICABLE CABLE
SPECIFICATIONS
TEST METHOD
ITEM
REQUIREMENTS
QT AT
CONSTRUCTION
GENERAL EXAMINATION
MARKING
X
X
X
X
VISUALLY AND BY MEASURING INSTRUMENT.
CONFIRMED VISUALLY.
ACCORDING TO DRAWING.
ELECTRIC CHARACTERISTICS
5
m MAX.
M MIN.
X
X
X
X
X
X
CONTACT RESISTANCE
CONTACT SHALL BE MEASURED AT DC 1 A. (MIL-C-2316)
5000
INSULATION RESISTANCE
500
V DC.(MIL-STD-1344 3003)
VOLTAGE PROOF
2000
V AC. FOR 1 min.(MIL-STD-1344 3001)
NO FLASHOVER OR BREAKDOWN.
MECHANICAL CHARACTERISTICS
1.56200.003
CONTACT INSERTION AND
INSERTION AND WITHDRAWAL FORCES : 0.6 N MIN.
BY STEEL GAUGE.
X
X
X
X
-
-
-
-
WITHDRAWAL FORCES
CONNECTOR INSERTION AND
WITHDRAWAL FORCES
MEASURED BY APPLICABLE CONNECTOR. (WITHOUT LOCK
MECHANISM)
INSERTION AND WITHDRAWAL FORCES : 110 N MAX.
CONTACT RESISTANCE:
7.5
m MAX.
MECHANICAL OPERATION
500 TIMES INSERTIONS AND EXTRACTIONS.
(MIL-C-5015 4,6,12,2)
①NO ELECTRICAL DISCONTINUITY OF 10 s.
②NO DAMAGE, CRACK AND LOOSENESS OF PARTS.
VIBRATION
SHOCK
FREQUENCY: 10 TO 500 Hz,SINGLE AMPLITUDE 0.75 mm,
98 m/s2 AT 3h, FOR 3 DIRECTIONS.
(MIL-STD-1344 2005,CONDITION Ⅱ)
490 m/s2 DURATIONS OF PULSE 11 ms AT 3 TIMES
FOR 3 DIRECTIONS. (MIL-STD-1344 2004,CONDITION E)
①NO ELECTRICAL DISCONTINUITY OF 10 s.
②NO DAMAGE, CRACK AND LOOSENESS OF PARTS.
X
X
-
-
ENVIRONMENTAL CHARACTERISTICS
DAMP HEAT
EXPOSED AT 71℃, 95%,336h.(MIL-C-5015 4,6,10)
① INSULATION RESISTANCE: 50 MΩ MIN.
(AT HIGH HUMIDITY).
(STEADY STATE)
② INSULATION RESISTANCE: 500 MΩ MIN.
(AT DRY).
③ NO DAMAGE, CRACK AND LOOSENESS OF PARTS.
① INSULATION RESISTANCE: 5000 MΩ MIN..
② NO DAMAGE, CRACK AND LOOSENESS OF PARTS.
RAPID CHANGE OF TEMPERATURE TEMPERATURE -55→ R/T(2) → +125 → R/T ℃
TIME 30 → 10 TO 15 → 30 → 10 TO 15 min
X
-
UNDER 5 CYCLES. (MIL-C-5015 4,6,4)
SEALING(3)
EXPOSED AT A DEPTH OF 1.8 m FOR 48 h.
NO WATER PENETRATION INSIDE CONNECTOR.
NO AIR BUBBLES FROM CONNECTOR INTERFACE.
X
X
-
-
AIRTIGHTNESS(3)
APPLY AIR PRESSURE 40 kPa FOR 30 s TO INSIDE
CONNECTOR.
EXPOSED IN 5 SALT WATER SPRAY FOR 48 h.
(MIL-STD-1344 1001 CONDITION B)
CORROSION SALT MIST
OIL RESISTING(3)
NO HEAVY CORROSION RUIN THE FUNCTION.
NO OIL SEEPAGE INSIDE CONNECTOR.
X
X
X
X
-
-
-
-
DROP CUTTING OIL FOR 48 HOURS AT THE RATE OF 0.5
L/h.(JIS B 6015)
RESISTANCE TO SOLDERING
HEAT
SOLDERED AT SOLDER TEMPERATURE, +380℃±10℃ FOR
SOLDERING DURATION, 10±1 s.
NO DEFORMATION OF CASE OF EXCESSIVE LOOSENESS
OF THE TERMINALS.
SOLDERABILITY
SOLDERED AT SOLDER TEMPERATURE, +350℃±10℃ FOR
SOLDERING DURATION, 5±1 s.
WETTING ON SOLDER SURFACE.
NO SOLDER CLUSTER.
COUNT
DESCRIPTION OF REVISIONS
DESIGNED
CHECKED
DATE
△
0
REMARK
APPROVED
CHECKED
DESIGNED
HY.KOBAYASHI
HY.KOBAYASHI
HY.KISHI
18.06.08
18.06.08
18.06.08
NOTES (1) 13 A RATED CURRENT IS THE MAXIMUM CURRENT FLOW PER CONTACT.
BUT THE CURRENT CAPACITY OF WHOLE IS CONNECTOR 44.2 A MAX..
(2) R/T:ROOM TEMPERATURE
(3) SEALING AND AIRTIGHTNESS SHALL BE TESTED BY APPLICABLE CONNECTOR.
DRAWN
HY.KISHI
18.06.08
Unless otherwise specified, refer to IEC 60512(JIS C 5402).
Note QT:Qualification Test AT:Assurance Test X:Applicable Test
DRAWING NO.
PART NO.
CODE NO.
ELC-036138-77-00
H/MS3106A20-29SW(77)
SPECIFICATION SHEET
HIROSE ELECTRIC CO., LTD.
0
△
1/1
CL120-0611-7-77
FORM HD0011-2-1