HIP6301V, HIP6302V
TM
Data Sheet
March 2002
FN9034.1
Current sensing is accomplished by reading the voltage
Microprocessor CORE Voltage Regulator
Multi-Phase Buck PWM Controller
developed across the lower MOSFETs during their
conduction intervals. Current sensing provides the needed
signals for precision droop, channel-current balancing, load
sharing, and over-current protection. This saves cost by
taking advantage of the power device’s parasitic on
resistance.
The HIP6301V and HIP6302V control microprocessor core
voltage regulation by driving up to four synchronous-rectified
buck channels in parallel. Multi-phase buck converter
architecture uses interleaved timing to multiply ripple
frequency and reduce input and output ripple currents.
Lower ripple results in fewer components, lower component
cost, reduced power dissipation, and smaller implementation
area. The HIP6301V is a versatile two to four phase
controller and the HIP6302V is a cost-saving dedicated
two-phase controller.
Features
• Multi-Phase Power Conversion
• Precision CORE Voltage Regulation
- ±0.8% System Accuracy Over Temperature
The HIP6301V and HIP6302V are exact pin compatible
replacements for their predecessor parts, the HIP6301 and
HIP6302. They are the first controllers to incorporate
Dynamic VID™ technology to manage the output voltage
and current during on-the-fly DAC changes. Using Dynamic
VID, the HIP6301V and HIP6302V detect changes in the VID
code and gradually change the reference in 25mV
increments until reaching the new value. By gradually
changing the reference setting, inrush current and the
accompanying voltage swings remain negligibly small.
• Microprocessor Voltage Identification Input
- Dynamic-VID Technology
- 5-Bit VID Decoder
• Precision Channel-Current Balance
• Overcurrent Protection
• Lossless Current Sensing
• Programmable “Droop” Voltage
• Fast Transient Response
Intersil offers a wide range of MOSFET drivers to form highly
integrated solutions for high-current, high slew-rate
applications. The HIP6301V and HIP6302V regulate output
voltage, balance load currents and provide protective
functions for two to four synchronous-rectified buck
converter channels. These parts feature an integrated high-
bandwidth error amplifier for fast, precise regulation and a
five-bit DAC for the digital interface to program the 0.8%
accuracy. A window comparator toggles PGOOD if the
output voltage moves out of range and acts to protect the
load in case of over voltage.
• Selection of 2, 3, or 4 Phase Operation
• High Ripple Frequency (100kHz to 6MHz)
Ordering Information
o
PART NUMBER
HIP6301VCB
TEMP. ( C)
PACKAGE
PKG. NO.
0 to 70
20 Ld SOIC
M20.3
HIP6301VCB-T
HIP6302VCB
20 Ld SOIC Tape and Reel
0 to 70 16 Ld SOIC
M16.15
HIP6302VCB-T
16 Ld SOIC Tape and Reel
Pinouts
HIP6301V (SOIC)
TOP VIEW
HIP6302V (SOIC)
TOP VIEW
1
2
1
2
3
4
5
6
7
8
20
19
18
17
16
15
14
13
12
11
16
15
14
VID4
VID4
VID3
V
V
CC
CC
VID3
VID2
PGOOD
ISEN1
PGOOD
PWM4
ISEN4
ISEN1
PWM1
PWM2
ISEN2
ISEN3
PWM3
3
VID2
4
13 PWM1
VID1
VID1
5
12
11
10
9
VID0
VID0
PWM2
ISEN2
VSEN
GND
6
COMP
FB
COMP
FB
7
8
FS/DIS
FS/DIS
GND
9
10
VSEN
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2002. All Rights Reserved
1
Dynamic VID™ is a trademark of Intersil Americas Inc.