HIP6018B
Data Sheet
May 1999
File Number 4586.1
Advanced PWM and Dual Linear Power
Control
Features
• Provides 3 Regulated Voltages
The HIP6018B provides the power control and protection for
three output voltages in high-performance microprocessor
and computer applications. The IC integrates a PWM
controllers, a linear regulator and a linear controller as well
as the monitoring and protection functions into a single
package. The PWM controller regulates the microprocessor
core voltage with a synchronous-rectified buck converter.
The linear controller regulates power for the GTL bus and
the linear regulator provides power for the clock driver circuit.
- Microprocessor Core, Clock and GTL Power
• Drives N-Channel MOSFETs
• Operates from +3.3V, +5V and +12V Inputs
• Simple Single-Loop PWM Control Design
- Voltage-Mode Control
• Fast Transient Response
- High-Bandwidth Error Amplifier
- Full 0% to 100% Duty Ratios
The HIP6018B includes an Intel-compatible, TTL 5-input
digital-to-analog converter (DAC) that adjusts the core PWM
output voltage from 2.1VDC to 3.5VDC in 0.1V increments
and from 1.3VDC to 2.05VDC in 0.05V steps. The precision
reference and voltage-mode control provide ±1% static
regulation. The linear regulator uses an internal pass device
to provide 2.5V ±2.5%. The linear controller drives an
external N-channel MOSFET to provide 1.5V ±2.5%.
• Excellent Output Voltage Regulation
- Core PWM Output: ±1% Over Temperature
- Other Outputs: ±2.5% Over Temperature
• TTL-Compatible 5-Bit Digital-to-Analog Core Output
Voltage Selection
- Wide Range . . . . . . . . . . . . . . . . . . . 1.3V
- 0.1V Steps . . . . . . . . . . . . . . . . . . . . 2.1V
to 3.5V
to 3.5V
DC
DC
DC
DC
DC
The HIP6018B monitors all the output voltages. A single
Power Good signal is issued when the core is within 10% of
the DAC setting and the other levels are above their under-
voltage levels. Additional built-in over-voltage protection for
the core output uses the lower MOSFET to prevent output
voltages above 115% of the DAC setting. The PWM over-
current function monitors the output current by using the
- 0.05V Steps . . . . . . . . . . . . . . . . . . 1.3V
to 2.05V
DC
• Power-Good Output Voltage Monitor
• Microprocessor Core Voltage Protection Against Shorted
MOSFET
• Over-Voltage and Over-Current Fault Monitors
- Does Not Require Extra Current Sensing Element,
voltage drop across the upper MOSFET’s r
,
DS(ON)
Uses MOSFET’s r
DS(ON)
eliminating the need for a current sensing resistor.
• Small Converter Size
- Constant Frequency Operation
Pinout
- 200kHz Free-Running Oscillator; Programmable from
50kHz to over 1MHz
HIP6018B
(SOIC)
TOP VIEW
Applications
24
23
22
21
20
19
18
17
16
15
14
13
VCC
VID4
1
2
3
4
5
6
7
8
9
UGATE1
PHASE1
LGATE1
PGND
•
•
Full Motherboard Power Regulation for Computers
Low-Voltage Distributed Power Supplies
VID3
VID2
Ordering Information
VID1
OCSET1
VSEN1
FB1
TEMP.
PKG.
NO.
VID0
o
PART NUMBER RANGE ( C)
PACKAGE
24 Ld SOIC
PGOOD
FAULT
SS
HIP6018BCB
0 to 70
M24.3
COMP1
FB3
RT 10
FB2 11
VIN2 12
DRIVE3
GND
VOUT2
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
2-238